Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › from 2020.11
RM37A0E _58 Vehicle Interior _086884 DOOR LOCK _0417739 WIRELESS DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). (ex. If a door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1242 Wireless Door Lock Tuner Circuit Malfunction
·

Short to ground in RDAM terminal circuit between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short to ground in RDAM terminal circuit when voltage (5 V) is not being output from terminal RCO


·

Wire harness or connector

·

Door control receiver

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

for 12 Pin Type


B526703E04
5.094,2.948 6.615,3.438 1.521,0.49 10 false Certification ECU (Smart Key ECU Assembly) 1.635,0.781 2.552,0.979 0.917,0.198 10 false DATA 1.823,1.438 2.74,1.635 0.917,0.198 10 false +5 0.24,3.063 2.781,3.583 2.542,0.521 10 false Electrical Key and Tire Pressure Warning ECU and Receiver 0.24,2.896 1.156,3.094 0.917,0.198 10 false M51 5.177,1.448 6.094,1.646 0.917,0.198 10 false RCO 5.167,0.792 6.083,0.99 0.917,0.198 10 false RDAM 2.094,1.438 2.51,1.677 0.417,0.24 10 false 8 2.063,2.073 2.479,2.313 0.417,0.24 10 false 12 4.833,0.677 5.25,0.917 0.417,0.24 10 false 19 4.802,0.865 5.229,1.094 0.427,0.229 10 false M5 4.833,1.344 5.25,1.583 0.417,0.24 10 false 18 4.823,1.979 5.24,2.219 0.417,0.24 10 false 18 4.792,2.177 5.208,2.417 0.417,0.24 10 false H48 5.177,2.188 5.594,2.427 0.417,0.24 10 false E 1.698,2.188 2.115,2.427 0.417,0.24 10 false GND 4.802,1.521 5.229,1.75 0.427,0.229 10 false M5 6.281,1.208 7.156,1.406 0.875,0.198 10 false IC 5.865,0.365 6.781,0.563 0.917,0.198 10 false 12 V 2.083,0.76 2.5,1.083 0.417,0.323 10 false 2


for 5 Pin Type


B526703E06
5.094,2.948 6.615,3.438 1.521,0.49 10 false Certification ECU (Smart Key ECU Assembly) 1.635,0.781 2.552,0.979 0.917,0.198 10 false DATA 1.823,1.438 2.74,1.635 0.917,0.198 10 false +5 0.313,3.063 3.125,3.26 2.813,0.198 10 false Smart Door Control Receiver Assembly 0.323,2.896 1.24,3.094 0.917,0.198 10 false M52 5.177,1.448 6.094,1.646 0.917,0.198 10 false RCO 5.167,0.792 6.083,0.99 0.917,0.198 10 false RDAM 2.094,1.438 2.51,1.677 0.417,0.24 10 false 4 2.104,2.073 2.521,2.313 0.417,0.24 10 false 1 4.833,0.677 5.25,0.917 0.417,0.24 10 false 19 4.802,0.865 5.229,1.094 0.427,0.229 10 false M5 4.833,1.344 5.25,1.583 0.417,0.24 10 false 18 4.823,1.979 5.24,2.219 0.417,0.24 10 false 18 4.792,2.177 5.208,2.417 0.417,0.24 10 false H48 5.177,2.188 5.594,2.427 0.417,0.24 10 false E 1.698,2.188 2.115,2.427 0.417,0.24 10 false GND 4.802,1.521 5.229,1.75 0.427,0.229 10 false M5 6.281,1.208 7.156,1.406 0.875,0.198 10 false IC 5.865,0.365 6.781,0.563 0.917,0.198 10 false 12 V 2.083,0.76 2.5,1.083 0.417,0.323 10 false 5


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, the performance of the entry function and wireless function may be affected.

·

The detection conditions of this DTC cannot be met within 10 seconds of the ignition switch being turned from off to ON or ON to off.

·

Make sure that there are no electrical key transmitter sub-assemblies in the vehicle.

·

When replacing the electrical key and tire pressure warning ECU and receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

·

If the electrical key and tire pressure warning ECU and receiver has been replaced, it is necessary to perform initialization (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs to the electrical key and tire pressure warning ECU and receiver.



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the M51*1 or M52*2 door control receiver connector.

*1: for 12 Pin Type

*2: for 5 Pin Type



b.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B440804C49
4.5,0.333 4.917,0.583 0.417,0.25 3.24,0.333 3.625,0.563 0.385,0.229 3.896,1.438 3.938,2.073 3.938,2.073 4.083,2.073 false 3.823,1.438 3.906,2.458 3.906,2.458 4.052,2.458 false 5.208,1.448 5.25,2.083 5.25,2.083 5.396,2.083 false 3.333,0.354 3.792,0.552 0.458,0.198 10 false M5 4.583,0.365 5.042,0.563 0.458,0.198 10 false H48 4.135,2.01 4.594,2.208 0.458,0.198 10 false RCO 4.083,2.375 4.635,2.531 0.552,0.156 10 false RDAM 5.438,2.031 5.99,2.188 0.552,0.156 10 false E 0.26,0.167 0.719,0.365 0.458,0.198 10 false *a 2.188,0.365 2.5,0.563 0.313,0.198 10 false *A
*A for Gasoline Model - -
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
H48-18 (E) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
M5-19 (RDAM) - H48-18 (E) Always 11 to 14 V
M5-18 (RCO) - H48-18 (E) Always Below 1 V → 4.5 to 5.5 V pulse generation at regular intervals



Result:
Result Proceed to
OK (for 12 Pin Type) A
OK (for 5 Pin Type) B
NG C



A

REPLACE ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER

B

REPLACE SMART DOOR CONTROL RECEIVER ASSEMBLY

C

2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the M5 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 12 Pin Type
Tester Connection Condition Specified Condition
M51-2 (DATA) - M5-19 (RDAM) Always Below 1 Ω
M51-8 (+5) - M5-18 (RCO) Always Below 1 Ω
M51-12 (GND) - Body ground Always Below 1 Ω
M51-2 (DATA) or M5-19 (RDAM) - Other terminals and body ground Always 10 kΩ or higher
M51-8 (+5) or M5-18 (RCO) - Other terminals and body ground Always 10 kΩ or higher

for 5 Pin Type
Tester Connection Condition Specified Condition
M52-5 (DATA) - M5-19 (RDAM) Always Below 1 Ω
M52-4 (+5) - M5-18 (RCO) Always Below 1 Ω
M52-1 (GND) - Body ground Always Below 1 Ω
M52-5 (DATA) or M5-19 (RDAM) - Other terminals and body ground Always 10 kΩ or higher
M52-4 (+5) or M5-18 (RCO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR