Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086877 AUDIO / VIDEO _0420540 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B1324  Lost Communication with Meter  


DESCRIPTION

These DTCs are stored when communication between the radio and display receiver assembly and combination meter assembly is not possible.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter CAN reception error
·

Local bus communication line

·

Combination meter power source circuit

·

Combination meter assembly

·

Radio and display receiver assembly

·

Harness or connector

·

No. 6 junction connector

·

Stop and start system*



*: w/ Stop and Start System


HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E433150E02
2.948,1.646 4.125,2.031 1.177,0.385 10 false Combination Meter Assembly 2.958,1.49 3.406,1.781 0.448,0.292 10 false H21 3.75,1.042 4.198,1.333 0.448,0.292 10 false ES 3.188,0.469 3.635,0.76 0.448,0.292 10 false B 3.188,0.885 3.635,1.177 0.448,0.292 10 false IG+ 2.938,0.375 3.385,0.667 0.448,0.292 10 false 40 2.938,0.792 3.385,1.083 0.448,0.292 10 false 39 4.042,0.344 4.49,0.635 0.448,0.292 10 false 36 4.042,0.615 4.49,0.906 0.448,0.292 10 false 37 4.042,0.927 4.49,1.219 0.448,0.292 10 false 21 4.406,0.344 4.854,0.635 0.448,0.292 10 false 9 4.344,0.604 4.792,0.896 0.448,0.292 10 false 20 5.563,0.333 6.01,0.625 0.448,0.292 10 false 11 5.573,0.615 6.021,0.906 0.448,0.292 10 false 22 5.938,0.333 6.385,0.625 0.448,0.292 10 false 5 5.938,1.219 7.125,1.813 1.188,0.594 10 false Radio and Display Receiver Assembly 5.938,0.615 6.385,0.906 0.448,0.292 10 false 6 5.948,1.063 6.896,1.625 0.948,0.563 10 false H2 6.115,0.458 6.646,0.74 0.531,0.281 10 false CNH1 6.115,0.76 6.667,1.052 0.552,0.292 10 false CNL1 0.271,0.438 2.229,0.792 1.958,0.354 10 false from Auxiliary Battery 0.156,0.875 2.115,1.229 1.958,0.354 10 false from IG2-NO. 2 Relay*1 1.833,0.604 2.979,0.938 1.146,0.333 10 false ECU-DCC NO. 2 1.99,1.031 2.844,1.375 0.854,0.344 10 false METER-IG2 4.281,2.094 6.625,2.375 2.344,0.281 10 false No. 6 Junction Connector 4.281,1.938 6.24,2.292 1.958,0.354 10 false H95 0.99,2.365 3.594,2.74 2.604,0.375 10 false : Local Bus Communication Line 3.729,0.469 4.177,0.76 0.448,0.292 10 false TX+ 3.75,0.75 4.198,1.042 0.448,0.292 10 false TX- 0.146,1.313 2.438,1.656 2.292,0.344 10 false from Engine Stop and Start ECU*2 0.406,1.74 2.563,2.135 2.156,0.396 10 false *1: w/o Stop and Start System 0.406,2.021 2.552,2.354 2.146,0.333 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)
a.

Disconnect the H21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H21-21 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H21-40 (B) - Body ground*1 Ignition switch off 11 to 14 V
H21-40 (B) - Body ground*2 Always 11 to 14 V
H21-39 (IG+) - Body ground Ignition switch ON 11 to 14 V*3
10.5 to 16 V*4


*1: for HV Model

*2: for Gasoline Model

*3: w/o Stop and Start System

*4: w/ Stop and Start System



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H95 No. 6 junction connector.


c.

Connect the H21 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H95-9 - H95-20 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H95 No. 6 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H95-11 - H95-22 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 6 JUNCTION CONNECTOR

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H2 radio and display receiver assembly connector.


c.

Connect the H95 No. 6 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-5 (CNH1) - H2-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H21 combination meter assembly connector.


c.

Connect the H95 No. 6 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H21-36 (TX+) - H21-37 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR