Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2020.11
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0420032 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Power Source Circuit  


DESCRIPTION

Based on changes in the power source voltage, the main body ECU (multiplex network body ECU) can detect if the auxiliary battery has been disconnected and reconnected.

WIRING DIAGRAM

B601462E01
0.344,1.26 2.177,1.458 1.833,0.198 10 false from Door Control Battery*2*3 2.031,0.938 3.865,1.135 1.833,0.198 10 false ECU-B NO. 3*1 3.542,2.427 5.156,2.885 1.615,0.458 10 false Instrument Panel Junction Block Assembly 3.354,0.813 5.188,1.01 1.833,0.198 10 false 4B 3.365,0.583 5.198,0.781 1.833,0.198 10 false 23 5.5,2.719 7.135,3.177 1.635,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 5.51,2.542 5.99,2.719 0.479,0.177 10 false MB 5.333,0.698 5.646,0.896 0.313,0.198 10 false 31 5.615,0.813 6.229,1.01 0.615,0.198 10 false BECU 0.323,0.802 1.906,0.99 1.583,0.188 10 false from Auxiliary Battery*1 0.271,3.042 4.396,3.24 4.125,0.198 10 false *3: w/ Door Control Battery 0.271,3.365 4.396,3.563 4.125,0.198 10 false *4: w/o Door Control Battery 1.01,1.708 2.844,1.906 1.833,0.198 10 false from Auxiliary Battery*2*4 3.792,1.865 5.625,2.063 1.833,0.198 10 false ECU-DCC NO. 2*2*4 0.271,2.354 4.396,2.552 4.125,0.198 10 false *1: for HV Model 0.271,2.698 4.396,2.896 4.125,0.198 10 false *2: for Gasoline Model 3.385,1.5 5.219,1.698 1.833,0.198 10 false 1 3.354,1.698 5.188,1.896 1.833,0.198 10 false 4C

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SUPPLY)
a.

Disconnect the 4B instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4B-23 - Body ground*1, *2*3 Ignition switch off*1
Always*2
8.5 V or higher
4C-1 - Body ground*2*4


*1: for HV Model

*2: for Gasoline Model

*3: w/ Door Control Battery

*4: w/o Door Control Battery



Result:
Proceed to
OK
NG



OK

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B601463C01
1.406,0.354 1.854,0.615 0.448,0.26 4.677,0.427 5.125,0.688 0.448,0.26 3.5,1.99 3.948,2.25 0.448,0.26 6.333,1.917 6.552,1.917 6.552,1.917 6.552,1.25 false 0.24,0.208 0.552,0.406 0.313,0.198 10 false *a 1.542,0.396 1.854,0.594 0.313,0.198 10 false 4B 4.792,0.469 5.104,0.667 0.313,0.198 10 false MB 3.625,2.031 3.938,2.229 0.313,0.198 10 false 4C 5.896,1.844 6.479,2.125 0.583,0.281 10 false BECU
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4B-23 - MB-31 (BECU)*1, *2*3 Always Below 1 Ω
4C-1 - MB-31 (BECU)*2*4


*1: for HV Model

*2: for Gasoline Model

*3: w/ Door Control Battery

*4: w/o Door Control Battery



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY