Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory) › from 2020.11
RM37A0E _59 Vehicle Exterior _086891 MIRROR (EXT) _0420033 POWER MIRROR CONTROL SYSTEM(w/ Memory) U

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)


B343031C61
3.896,0.083 4.313,0.333 0.417,0.25 1.854,0.083 2.271,0.333 0.417,0.25 2.708,0.094 3.125,0.344 0.417,0.25 4.646,0.083 5.063,0.333 0.417,0.25 4,0.125 4.458,0.323 0.458,0.198 10 false J23 1.938,0.115 2.396,0.313 0.458,0.198 10 false z17 2.813,0.135 3.271,0.333 0.458,0.198 10 false z16 2.313,0.125 2.771,0.323 0.458,0.198 10 false *A 3.188,0.135 3.646,0.333 0.458,0.198 10 false *B 4.375,0.125 4.833,0.323 0.458,0.198 10 false *A 4.781,0.135 5.24,0.333 0.458,0.198 10 false J7 5.115,0.125 5.573,0.323 0.458,0.198 10 false *B
*A for LHD *B for RHD


a.

Disconnect the J23*1 or J7*2 outer mirror control ECU assembly (driver door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J23-14 (BDR) - Body ground +B power supply Ignition switch off*1
Always*2
11 to 14 V
J23-6 (CPUB) - Body ground +B power supply Ignition switch off*1
Always*2
11 to 14 V
J23-5 (SIG) - Body ground Ignition power supply Ignition switch off → ON Below 1 V → 11 to 14 V
J23-7 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model


for RHD:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J7-14 (BDR) - Body ground +B power supply Ignition switch off*1
Always*2
11 to 14 V
J7-6 (CPUB) - Body ground +B power supply Ignition switch off*1
Always*2
11 to 14 V
J7-5 (SIG) - Body ground Ignition power supply Ignition switch off → ON Below 1 V → 11 to 14 V
J7-7 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the J23*1 or J7*2 outer mirror control ECU assembly (driver door) connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
z17-3 (MR) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly (driver door) being retracted 11 to 14 V
Outer rear view mirror assembly (driver door) stopped Below 1 V
z17-11 (MF) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly (driver door) returning 11 to 14 V
Outer rear view mirror assembly (driver door) stopped Below 1 V
z17-1 (MV) - z17-10 (M+) Vertical mirror motor drive voltage Driver door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
z17-10 (M+) - z17-1 (MV) Vertical mirror motor drive voltage Driver door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
z17-10 (M+) - z17-9 (MH) Horizontal mirror motor drive voltage Driver door mirror surface moving right → stopped 11 to 14 V → Below 1 V
z17-9 (MH) - z17-10 (M+) Horizontal mirror motor drive voltage Driver door mirror surface moving left → stopped 11 to 14 V → Below 1 V
z17-5 (VC) - z17-14 (E1) Mirror position sensor power supply Ignition switch ON 4.55 to 5.45 V
Ignition switch off Below 1 V
z17-6 (VSRL) - J23-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z17-13 (HSRL) - J23-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
J23-3 (M2) - J23-7 (GND) M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
J23-2 (M1) - J23-7 (GND) M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
J23-1 (MM) - J23-7 (GND) SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V
z17-4 (+) - z17-12 (-) Mirror heater relay drive voltage Mirror heater switch (rear window defogger switch) on 11 to 14 V
z17-2 (MLP+) - z17-12 (-) Foot light drive output Foot light off → on Below 1 V → 11 to 14 V

for RHD:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
z16-3 (MR) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly (driver door) being retracted 11 to 14 V
Outer rear view mirror assembly (driver door) stopped Below 1 V
z16-11 (MF) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly (driver door) returning 11 to 14 V
Outer rear view mirror assembly (driver door) stopped Below 1 V
z16-1 (MV) - z16-10 (M+) Vertical mirror motor drive voltage Driver door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
z16-10 (M+) - z16-1 (MV) Vertical mirror motor drive voltage Driver door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
z16-10 (M+) - z16-9 (MH) Horizontal mirror motor drive voltage Driver door mirror surface moving right → stopped 11 to 14 V → Below 1 V
z16-9 (MH) - z16-10 (M+) Horizontal mirror motor drive voltage Driver door mirror surface moving left → stopped 11 to 14 V → Below 1 V
z16-5 (VC) - z16-14 (E1) Mirror position sensor power supply Ignition switch ON 4.55 to 5.45 V
Ignition switch off Below 1 V
z16-6 (VSSR) - J7-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z16-13 (HSSR) - J7-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
J7-3 (M2) - J7-7 (GND) M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
J7-2 (M1) - J7-7 (GND) M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
J7-1 (MM) - J7-7 (GND) SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V
z16-4 (+) - z16-12 (-) Mirror heater relay drive voltage Mirror heater switch (rear window defogger switch) on 11 to 14 V
z16-2 (MLP+) - z16-12 (-) Foot light drive output Foot light off → on Below 1 V → 11 to 14 V



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)


B343031C62
3.896,0.083 4.313,0.333 0.417,0.25 1.854,0.083 2.271,0.333 0.417,0.25 2.708,0.094 3.125,0.344 0.417,0.25 4.646,0.083 5.063,0.333 0.417,0.25 4.052,0.125 4.51,0.323 0.458,0.198 10 false J7 1.938,0.115 2.396,0.313 0.458,0.198 10 false z16 2.813,0.135 3.271,0.333 0.458,0.198 10 false z17 2.313,0.125 2.771,0.323 0.458,0.198 10 false *A 3.188,0.135 3.646,0.333 0.458,0.198 10 false *B 4.375,0.125 4.833,0.323 0.458,0.198 10 false *A 4.74,0.135 5.198,0.333 0.458,0.198 10 false J23 5.115,0.125 5.573,0.323 0.458,0.198 10 false *B
*A for LHD *B for RHD


a.

Disconnect the J7*1 or J23*2 outer mirror control ECU assembly (front passenger door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J7-14 (BDR) - Body ground +B power supply Ignition switch off*1
Always*2
11 to 14 V
J7-6 (CPUB) - Body ground +B power supply Ignition switch off*1
Always*2
11 to 14 V
J7-5 (SIG) - Body ground Ignition power supply Ignition switch off → ON Below 1 V → 11 to 14 V
J7-7 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model


for RHD:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J23-14 (BDR) - Body ground +B power supply Ignition switch off*1
Always*2
11 to 14 V
J23-6 (CPUB) - Body ground +B power supply Ignition switch off*1
Always*2
11 to 14 V
J23-5 (SIG) - Body ground Ignition power supply Ignition switch off → ON Below 1 V → 11 to 14 V
J23-7 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the J7*1 or J23*2 outer mirror control ECU assembly (front passenger door) connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
z16-3 (MR) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly (front passenger door) being retracted 11 to 14 V
Outer rear view mirror assembly (front passenger door) stopped Below 1 V
z16-11 (MF) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly (front passenger door) returning 11 to 14 V
Outer rear view mirror assembly (front passenger door) stopped Below 1 V
z16-1 (MV) - z16-10 (M+) Vertical mirror motor drive voltage Front passenger door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
z16-10 (M+) - z16-1 (MV) Vertical mirror motor drive voltage Front passenger door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
z16-10 (M+) - z16-9 (MH) Horizontal mirror motor drive voltage Front passenger door mirror surface moving right → stopped 11 to 14 V → Below 1 V
z16-9 (MH) - z16-10 (M+) Horizontal mirror motor drive voltage Front passenger door mirror surface moving left → stopped 11 to 14 V → Below 1 V
z16-5 (VC) - z16-14 (E1) Mirror position sensor power supply Ignition switch ON 4.55 to 5.45 V
Ignition switch off Below 1 V
z16-6 (VSSR) - J7-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z16-13 (HSSR) - J7-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z16-4 (+) - z16-12 (-) Mirror heater relay drive voltage Mirror heater switch (rear window defogger switch) on 11 to 14 V
z16-2 (MLP+) - z16-12 (-) Foot light drive output Foot light off → on Below 1 V → 11 to 14 V

for RHD:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
z17-3 (MR) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly (front passenger door) being retracted 11 to 14 V
Outer rear view mirror assembly (front passenger door) stopped Below 1 V
z17-11 (MF) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly (front passenger door) returning 11 to 14 V
Outer rear view mirror assembly (front passenger door) stopped Below 1 V
z17-1 (MV) - z17-10 (M+) Vertical mirror motor drive voltage Front passenger door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
z17-10 (M+) - z17-1 (MV) Vertical mirror motor drive voltage Front passenger door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
z17-10 (M+) - z17-9 (MH) Horizontal mirror motor drive voltage Front passenger door mirror surface moving right → stopped 11 to 14 V → Below 1 V
z17-9 (MH) - z17-10 (M+) Horizontal mirror motor drive voltage Front passenger door mirror surface moving left → stopped 11 to 14 V → Below 1 V
z17-5 (VC) - z17-14 (E1) Mirror position sensor power supply Ignition switch ON 4.55 to 5.45 V
Ignition switch off Below 1 V
z17-6 (VSRL) - J23-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z17-13 (HSRL) - J23-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z17-4 (+) - z17-12 (-) Mirror heater relay drive voltage Mirror heater switch (rear window defogger switch) on 11 to 14 V
z17-2 (MLP+) - z17-12 (-) Foot light drive output Foot light off → on Below 1 V → 11 to 14 V



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


B520311N39
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.385,4.573 5.823,4.823 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.292,6.198 5.729,6.448 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 3.469,7.677 3.781,7.875 0.313,0.198 10 false MB 4.292,0.219 4.604,0.417 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false H42 2.042,1.479 2.354,1.677 0.313,0.198 10 false H43 2.042,1.802 2.354,2 0.313,0.198 10 false H44 0.865,1.073 1.177,1.271 0.313,0.198 10 false 4D 0.865,1.656 1.177,1.854 0.313,0.198 10 false 4C 0.875,2.021 1.188,2.219 0.313,0.198 10 false 4E 0.896,2.25 1.208,2.448 0.313,0.198 10 false 4F 5.844,1.146 6.156,1.344 0.313,0.198 10 false 4B 5.844,1.76 6.156,1.958 0.313,0.198 10 false 4A 1.229,3.281 1.542,3.479 0.313,0.198 10 false H44 3.25,3.25 3.563,3.448 0.313,0.198 10 false H43 5.531,3.24 5.844,3.438 0.313,0.198 10 false H42 1.833,4.604 2.146,4.802 0.313,0.198 10 false 4A 1.24,6.198 1.552,6.396 0.313,0.198 10 false 4C 3.813,6.156 4.125,6.354 0.313,0.198 10 false 4D 5.427,6.219 5.74,6.417 0.313,0.198 10 false 4F 6.448,6.229 6.76,6.427 0.313,0.198 10 false 4E 5.51,4.604 5.823,4.802 0.313,0.198 10 false 4B

a.

Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
MB-31 (BECU) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
MB-32 (IG) - Body ground Ignition power supply (IG signal) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
MB-30 (ACC) - Body ground Ignition power supply (ACC signal) Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
MB-11 (GND1) - Body ground Ground Always Below 1 Ω
H42-19 (GND2) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



d.

Connect the main body ECU (multiplex network body ECU) connectors.


e.

Measure the voltage according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
H44-7 (MIRB) - H44-9 (MIRE) Mirror adjust switch signal
·

Ignition switch ACC

·

Mirror select switch L or R

·

Mirror adjust switch up


Below 1.7 V
·

Ignition switch ACC

·

Mirror select switch L or R

·

Mirror adjust switch right


Below 2.7 V
·

Ignition switch ACC

·

Mirror select switch L or R

·

Mirror adjust switch down


Below 3.5 V
·

Ignition switch ACC

·

Mirror select switch L or R

·

Mirror adjust switch left


Below 4 V
·

Ignition switch ACC

·

Mirror select switch L or R

·

Mirror adjust switch off


3.8 to 5 V
H44-8 (MIRS) - H44-9 (MIRE) Mirror select switch signal
·

Ignition switch ACC

·

Mirror select switch L


Below 2 V
·

Ignition switch ACC

·

Mirror select switch R


Below 1 V
·

Ignition switch ACC

·

Mirror select switch off


3.8 to 5 V
H44-16 (RET) - H44-9 (MIRE) Retractable outer mirror switch signal
·

Ignition switch ACC

·

Retractable outer mirror switch not in retract position


11 to 14 V
·

Ignition switch ACC

·

Retractable outer mirror switch in retract position


Below 1 V
H44-6 (AMR) - H44-9 (MIRE) Retractable outer mirror switch signal
·

Ignition switch ACC

·

Retractable outer mirror switch not in auto position


11 to 14 V
·

Ignition switch ACC

·

Retractable outer mirror switch in auto position


Below 1 V