Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL INJECTOR (for Direct Injection) › from 2020.11
RM37A0E _51 Engine / Hybrid System _086852 2GR-FKS FUEL _0417508 FUEL INJECTOR(for Direct Injection) A

2GR-FKS FUEL  FUEL INJECTOR(for Direct Injection)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during direct fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Replacement of direct fuel injector assembly

·

Replacement of fuel pressure sensor (fuel delivery pipe with sensor assembly LH)

·

Replacement of port fuel injector assembly

·

Replacement of fuel pressure sensor (fuel delivery pipe with sensor assembly)

·

Replacement of fuel pump assembly

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of air fuel ratio sensor

·

Replacement of heated oxygen sensor

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 23100X 1.REMOVE FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 23802B 2.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY

a.
A454394

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 2 fuel pipe sub-assembly.


b.

Remove the No. 2 fuel pipe sub-assembly from the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH.


Hide 23860 3.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY LH

a.
A393297

Disconnect the No. 6 engine wire connector and No. 7 engine wire connector.


b.
A393298

Disengage the 2 clamps to disconnect the No. 6 engine wire connector and No. 7 engine wire connector.


c.
A454395

Disconnect the fuel pressure sensor connector.


d.
A454396

Remove the bolt.


e.

Disengage the clamp to disconnect the No. 7 engine wire from the fuel delivery pipe with sensor assembly LH.


f.
A454397C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, 2 nuts and fuel delivery pipe with sensor assembly LH with the 3 direct fuel injector assemblies from the cylinder head LH.

NOTICE:
·

Make sure not to touch or strike the tips of the direct fuel injector assemblies.

·

Pull and remove the fuel delivery pipe with sensor assembly LH in a straight line without tilting it.




g.
A368871

Disconnect the 3 direct fuel injector assembly connectors.


Hide 23814E 4.REMOVE FUEL DELIVERY PIPE RH

a.
A454398

Remove the bolt.


b.

Disengage the clamp to disconnect the No. 6 engine wire from the fuel delivery pipe RH.


c.
A454399C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, 2 nuts and fuel delivery pipe RH with the 3 direct fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:
·

Make sure not to touch or strike the tips of the direct fuel injector assemblies.

·

Pull and remove the fuel delivery pipe RH in a straight line without tilting it.




d.
A368872

Disconnect the 3 direct fuel injector assembly connectors.


Hide 23250E 5.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

a.
A361016N01
2.333,2.75 3,3.052 0.667,0.302 10 true No. 2

Secure the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH in a vise between aluminum plates and pull out the 6 direct fuel injector assemblies.

NOTICE:
·

Pull and remove each direct fuel injector assembly in a straight line to avoid damaging the seal surface of the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH O-ring.

·

After removing the direct fuel injector assemblies, remove any O-rings, No. 1 fuel injector back-up rings and No. 3 fuel injector back-up rings remaining on the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH side.

·

Attach a tag or label with the corresponding cylinder number to each direct fuel injector assembly so that they can be installed to their original locations.

·

Cover the tip of each direct fuel injector assembly to prevent it from being damaged.




b.

Remove the nozzle holder clamp from each direct fuel injector assembly.


c.

Using needle nose pliers, remove the No. 3 fuel injector back-up ring from each direct fuel injector assembly.

NOTICE:

Do not damage the area that contacts the O-ring.



d.

Remove the O-ring and No. 1 fuel injector back-up ring from each direct fuel injector assembly.


e.

Remove the C-ring and injector vibration insulator from each direct fuel injector assembly.


Hide 23255A 6.REMOVE FUEL INJECTOR SEAL

a.
A361017

Using the tip of needle nose pliers, pinch and pull the fuel injector seal at several points to stretch it.

NOTICE:
·

Excessively pinching the fuel injector seal may damage the groove of the direct fuel injector assembly.

·

If a direct fuel injector assembly is dropped or the tip of the direct fuel injector assembly is struck, replace it with a new one.




b.

Remove the fuel injector seal from each direct fuel injector assembly.