Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C05262A  Steering Angle Sensor Module Signal Stuck In Range  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the steering angle sensor via CAN communication.

HINT:

When a malfunction occurs in the communication line to the steering angle sensor, U012687 is output.

If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.


DTC No. Detection Item DTC Detection Condition Trouble Area
C05262A Steering Angle Sensor Module Signal Stuck In Range Normal communication between the skid control ECU and the steering angle sensor and abnormal steering angle sensor zero point.
·

Steering angle sensor

·

Wire harness and connector

·

Backup boost converter circuit*



*: w/ Stop and Start System


WIRING DIAGRAM

C427355E02
0.833,0.542 1.292,0.74 0.458,0.198 10 false CANL 0.125,4.417 3.333,4.615 3.208,0.198 10 false Steering Angle Sensor 0.813,1.125 1.271,1.323 0.458,0.198 10 false CANH 0.927,1.771 1.385,1.969 0.458,0.198 10 false BAT 0.979,2.354 1.438,2.552 0.458,0.198 10 false IG1 0.906,3.802 1.365,4 0.458,0.198 10 false ESS 1.927,1.927 3.354,2.302 1.427,0.375 10 false ECU-DCC NO. 1 1.979,2.51 3,2.823 1.021,0.313 10 false ECU-IG1 NO. 2 2.552,3.073 3.073,3.271 0.521,0.198 10 false IG31 1.781,2.271 2.24,2.469 0.458,0.198 10 false *2 2.354,2.979 2.813,3.177 0.458,0.198 10 false 1 3.917,1.781 5.563,2.208 1.646,0.427 10 false from Auxiliary Battery 6.021,0.542 6.479,0.74 0.458,0.198 10 false CANL 6.021,1.135 6.479,1.333 0.458,0.198 10 false CANH 0.125,4.25 0.583,4.448 0.458,0.198 10 false H57 2.167,3.354 2.625,3.552 0.458,0.198 10 false H66 2.156,3.49 5.365,3.688 3.208,0.198 10 false Engine Stop and Start ECU*1 2.833,4.271 6.042,4.469 3.208,0.198 10 false : CAN Communication Line 5.583,4.135 6.042,4.333 0.458,0.198 10 false A39 5.573,4.302 7.156,4.75 1.583,0.448 10 false Skid Control ECU (Brake Actuator Assembly) 1.292,0.385 1.448,0.583 0.156,0.198 10 false 8 1.302,0.958 1.458,1.156 0.156,0.198 10 false 3 1.292,1.677 1.448,1.875 0.156,0.198 10 false 4 1.292,2.271 1.448,2.469 0.156,0.198 10 false 9 1.302,3.719 1.458,3.917 0.156,0.198 10 false 6 5.75,0.365 6.208,0.563 0.458,0.198 10 false 43 5.75,0.958 6.208,1.156 0.458,0.198 10 false 27 2.708,4.781 4.677,5.104 1.969,0.323 10 false *1: w/ Stop and Start System 2.708,5.156 4.813,5.448 2.104,0.292 10 false *2: w/o Stop and Start System 3.927,2.365 5.281,2.573 1.354,0.208 10 false from IG Circuit 2.208,2.25 2.365,2.448 0.156,0.198 10 false 2 2.219,1.625 2.375,1.823 0.156,0.198 10 false 2 2.604,1.625 2.76,1.823 0.156,0.198 10 false 1 2.625,2.25 2.781,2.448 0.156,0.198 10 false 1 1.854,3 2.313,3.198 0.458,0.198 10 false *1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC
a.

Turn the ignition switch to ON and check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING


b.

Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left.


c.

Check that no speed sensor and/or yaw rate sensor (airbag sensor assembly) DTCs are output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
DTC C05262A is output. A
CAN communication system DTCs are output. B
Speed sensor and/or yaw rate sensor (airbag sensor assembly) DTCs are output. C


HINT:
·

If a speed sensor, or the yaw rate sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering angle sensor may be stored even though the steering angle sensor is normal.

·

If speed sensor and/or yaw rate sensor (airbag sensor assembly) DTCs are output simultaneously, repair these malfunctions and then inspect the steering angle sensor.





A

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

B

C

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C418963C01
0.333,1.167 0.75,1.417 0.417,0.25 1.896,1.594 2.177,1.927 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 0.417,1.198 0.802,1.469 0.385,0.271 10 false H57 2.229,1.917 2.688,2.115 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Steering Angle Sensor)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the H57 steering angle sensor connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H57-9 (IG1) - Body ground Ignition switch ON 10.5 to 16 V*1
11 to 14 V*2


*1: w/ Stop and Start System

*2: w/o Stop and Start System



Result:
Result Proceed to
OK A
NG (w/ Stop and Start System) B
NG (w/o Stop and Start System) C



A

4.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)

B

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)
a.
C418963C02
0.333,1.167 0.75,1.417 0.417,0.25 1.917,1.24 2.177,0.5 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 0.417,1.188 0.802,1.458 0.385,0.271 10 false H57 2.104,0.313 2.563,0.51 0.458,0.198 10 false BAT
*a Front view of wire harness connector
(to Steering Angle Sensor)


Turn the ignition switch off.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H57-4 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H57-6 (ESS) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR