Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › from 2020.11
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0417656 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front bumper assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Front bumper assembly*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Front bumper assembly*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)

HINT:

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.

Target Adjustment (Triangle Target):

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Target Adjustment (Flat Surface Target):

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment:

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


PROCEDURE

Hide 53295E 1.REMOVE COOL AIR INTAKE DUCT SEAL

a.
B564074

Remove the 9 clips and cool air intake duct seal.


Hide 75086 2.DISCONNECT FRONT FENDER WHEEL OPENING MOULDING SUB-ASSEMBLY LH

a.
B564075C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front fender wheel opening moulding sub-assembly LH.


b.
B564076

Remove the 3 clips.


c.
B564077

Remove the screw.


d.
B564078C01
0.99,1.531 1.417,1.698 true 1.417,1.604 1.656,1.781 0.24,0.177 10 true *1
*1 Front Fender Liner LH
V113147

Remove in this Direction


Pull back the edge of the front fender liner LH and disengage the 4 claws by pushing the area indicated by the arrow in the illustration with a finger.

NOTICE:
·

Do not apply excessive force when pulling back the front fender liner LH.

·

To avoid damaging the claws, do not forcibly pull the front fender wheel opening moulding sub-assembly LH.




e.

Disengage the 2 clips and disconnect the front fender wheel opening moulding sub-assembly LH.


f.

Remove the 2 clips from the front fender wheel opening moulding sub-assembly LH.


Hide 75085A 3.DISCONNECT FRONT FENDER WHEEL OPENING MOULDING SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 4.REMOVE FRONT BUMPER ASSEMBLY

a.
B570446C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front bumper assembly.

HINT:

Use the same procedure for the RH side and LH side.



b.
B564081

Remove the 10 screws.


c.
B564082

Remove the 4 bolts.


d.
B570447

Disengage the 6 claws.

HINT:

Use the same procedure for the RH side and LH side.



e.
B570448

Disengage the claw to remove the front bumper assembly.


f.
B564085

Disconnect each connector.

HINT:

Use the same procedure for the LH side and RH side.



g.

w/ Headlight Cleaner System:

i.
B570449

Disconnect the No. 1 headlight cleaner washer hose assembly.


ii.
B570450

Drain the washer fluid.

HINT:

Use a container to collect the washer fluid.