Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING › from 2020.11
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0417669 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof drip side finish moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75597 1.REMOVE ROOF DRIP SIDE FINISH MOULDING JOINT COVER (w/o Roof Rack)

a.
B565973C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V100155

Protective Tape


Apply protective tape around the roof drip side finish moulding joint cover as shown in the illustration.


b.

Disengage the 2 clips and 2 claws, and remove the 2 roof drip side finish moulding joint covers as indicated by the arrows, in the order shown in the illustration.


Hide 75552 2.REMOVE FRONT ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)

a.
B565975C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front roof drip side finish moulding.


b.

Using a moulding remover, disengage the clip and remove the front roof drip side finish moulding.

NOTICE:
·

Do not remove the roof drip side finish moulding clip.

·

If a roof drip side finish moulding clip is damaged or falls off, replace it with a new one.




Hide 75556C 3.REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)

a.
B565977C01
0.844,0.365 1.833,0.365 true 1.865,0.26 2.177,0.458 0.313,0.198 10 false *a
*a Matchmark
V100155

Protective Tape


Apply protective tape around the center roof drip side finish moulding.


b.

Place a matchmark on the vehicle body at the location indicated in the illustration.


c.

Using a moulding remover, disengage the clip and remove the center roof drip side finish moulding.

NOTICE:
·

Do not remove the roof drip side finish moulding clip.

·

If the roof drip side finish moulding clip is damaged or falls out, replace it with a new one.




Hide 75554 4.REMOVE REAR ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)

a.
B565979C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear roof drip side finish moulding.


b.

Using a moulding remover, disengage the clip and remove the rear roof drip side finish moulding.

NOTICE:
·

Do not remove the roof drip side finish moulding clip.

·

If the roof drip side finish moulding clip is damaged or falls out, replace it with a new one.




Hide 63470B 5.REMOVE ROOF RACK ASSEMBLY (w/ Roof Rack)

Hide 75554 6.REMOVE REAR ROOF DRIP SIDE FINISH MOULDING (w/ Roof Rack)

a.
B565981C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear roof drip side finish moulding.


b.

Using a moulding remover, disengage and remove the rear roof drip side finish moulding.

NOTICE:
·

Do not remove the roof drip side finish moulding clip.

·

If the roof drip side finish moulding clip is damaged or falls out, replace it with a new one.