The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during windshield glass sub-assembly removal/installation are shown below.
When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, front camera system, lane control system, road sign assist system, pre-collision system or lighting system (EXT) may not operate properly due to a difference in the transmissivity or black ceramic border.
When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, front camera system, lane control system, road sign assist system, pre-collision system or lighting system (EXT) may not operate properly due to a difference in the transmissivity or black ceramic border.
55708
1.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
75534
2.REMOVE WINDSHIELD OUTSIDE MOULDING LH
75533
3.REMOVE WINDSHIELD OUTSIDE MOULDING RH
Use the same procedure as for the LH side.
87810
4.REMOVE INNER REAR VIEW MIRROR ASSEMBLY
w/ EC Mirror: Click hereVehicle Interior>MIRROR (INT)>INNER REAR VIEW MIRROR (w/ EC Mirror)>REMOVAL
w/o EC Mirror: Click hereVehicle Interior>MIRROR (INT)>INNER REAR VIEW MIRROR (w/o EC Mirror)>REMOVAL
8646C
5.REMOVE FORWARD RECOGNITION CAMERA
89941
6.REMOVE RAIN SENSOR (w/ Rain Sensor)
81260A
7.REMOVE MAP LIGHT ASSEMBLY
62212B
8.REMOVE FRONT PILLAR GARNISH ASSEMBLY LH
62211U
9.REMOVE FRONT PILLAR GARNISH ASSEMBLY RH
Use the same procedure as for the LH side.
74610A
10.REMOVE ASSIST GRIP SUB-ASSEMBLY
74325
11.REMOVE VISOR BRACKET COVER (for LH Side)
74320
12.REMOVE VISOR ASSEMBLY LH
74325
13.REMOVE VISOR BRACKET COVER (for RH Side)
Use the same procedure as for the LH side.
74310
14.REMOVE VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74348
15.REMOVE VISOR HOLDER
16.SEPARATE ROOF HEADLINING ASSEMBLY
Disconnect the connector.
Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed.
Do not damage the roof headlining assembly or vehicle interior.
It is not necessary to completely remove the roof headlining assembly.
17.REMOVE WINDSHIELD GLASS SUB-ASSEMBLY
w/ Windshield Deicer System:
Disconnect the connector.
|
Protective Tape |
Apply protective tape to the area around the installation position of the windshield glass sub-assembly on the vehicle body to prevent it from being scratched.
| *1 | Windshield Glass |
| *2 | Windshield Outside Upper Moulding |
| *a | Cut |
Using a knife, cut off the windshield outside upper moulding as shown in the illustration.
| *a | Matchmark |
Place matchmarks on the windshield glass sub-assembly and vehicle body at the locations indicated in the illustration.
Matchmarks are not necessary if the windshield glass is not going to be reused.
When using a windshield knife:
Apply soapy water to the area around the adhesive.
| *a | Windshield Knife |
| *b | Aligned with Windshield Glass Sub-assembly |
|
Pull |
Insert a windshield knife into the adhesive between the windshield glass sub-assembly and vehicle body.
While keeping the windshield knife perpendicular to the outer surface of the windshield glass sub-assembly, cut the adhesive by pulling the windshield knife around the windshield glass sub-assembly.
Do not pry the windshield glass sub-assembly with the windshield knife.
Do not use a windshield knife to cut the adhesive on the lower side of the windshield glass sub-assembly.
When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.
Insert the windshield knife in an area where the gap between windshield glass sub-assembly and vehicle body is large.
When using piano wire:
| *1 | Windshield Glass Stopper |
| *a | Piano Wire |
Pass a piano wire between the vehicle body and windshield glass sub-assembly from the interior.
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut the adhesive by pulling the piano wire around the windshield glass sub-assembly.
When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.
To prevent the safety pad from being scratched when removing the windshield glass sub-assembly, place a plastic sheet between the piano wire and safety pad.
Disengage the windshield glass stoppers.
| *A | for 1-piece Type | *B | for 2-piece Type |
| *1 | No. 1 Windshield Glass Stopper | *2 | No. 2 Windshield Glass Stopper |
The No. 1 windshield glass stoppers and No. 2 windshield glass stoppers are installed to the windshield glass sub-assembly as shown in the illustration. Be careful not to damage the windshield glass sub-assembly when cutting the adhesive.
To prevent the windshield glass sub-assembly from falling when performing this operation, be sure to hold the windshield glass sub-assembly using suction cups.
Depending on the vehicle, either 1-piece type or 2-piece type stoppers may be present.
Using suction cups, remove the windshield glass sub-assembly.
Be careful not to drop the windshield glass sub-assembly.
Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.
56117A
18.REMOVE WINDOW GLASS ADHESIVE DAM
When reusing the windshield glass:
| *A | Back Side |
Using a scraper, remove the 2 window glass adhesive dams.
Be careful not to damage the windshield glass.
Be sure to replace the window glass adhesive dam with a new ones.
| *A | Back Side |
Using a scraper, remove the window glass adhesive dam.
Be careful not to damage the windshield glass.
Be sure to replace the window glass adhesive dam with a new ones.
75531F
19.REMOVE WINDSHIELD OUTSIDE UPPER MOULDING
When reusing the windshield glass:
| *A | Back Side |
Using a scraper, remove the windshield outside upper moulding.
Be careful not to damage the windshield glass.
Be sure to replace the windshield outside upper moulding with a new one.
20.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)
When reusing the windshield glass:
| *A | Back Side |
Using a scraper, remove the 2 No. 1 windshield glass stoppers.
Be careful not to damage the windshield glass.
Be sure to replace the 1-piece type No. 1 windshield glass stoppers with new 2-piece type No. 1 and No. 2 windshield glass stoppers.
56116C
21.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
When reusing the windshield glass:
| *A | Back Side |
Using a scraper, remove the 2 No. 2 windshield glass stoppers.
Be careful not to damage the windshield glass.
Be sure to replace the No. 2 windshield glass stoppers with new ones.
56115A
22.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Remove the 2 No. 1 windshield glass stoppers from the vehicle body.
Be sure to replace the No. 1 windshield glass stoppers with new ones.
56153C
23.REMOVE FRONT WINDOW INNER CENTER MOULDING
Perform the following procedure only when replacement of the front window inner center moulding is necessary.
| *A | Back Side |
| *a | Matchmark |
| *A | Back Side |
Place matchmarks on the windshield glass at the locations indicated in the illustration.
Using a scraper, remove the front window inner center moulding.
Be careful not to damage the windshield glass.
Be sure to replace the front window inner center moulding with a new one.
24.CLEAN WINDSHIELD GLASS
When reusing the windshield glass:
Using a scraper, remove any remaining adhesive dam and adhesive residue from the windshield glass.
Be careful not to damage the windshield glass.
Clean the outer circumference of the windshield glass with a non-residue solvent.
Do not touch the windshield glass surface after cleaning it.
Even if using a new windshield glass, clean it with a non-residue solvent.
25.CLEAN VEHICLE BODY
Clean and shape the contact surface of the vehicle body.
| *a | Vehicle Body |
|
Adhesive |
Using a knife, cut off any excess adhesive on the contact surface of the vehicle body as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 1.0 mm (0.0394 in.) or more |
Be careful not to damage the vehicle body.
Leave approximately 1.0 mm (0.0394 in.) of adhesive on the vehicle body.
Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.
Even if all of the adhesive has been removed, clean the vehicle body.