Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › from 2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0420115 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)


E360013N33
5.021,0.333 5.438,0.583 0.417,0.25 2.552,0.333 2.969,0.583 0.417,0.25 1.5,0.333 1.917,0.583 0.417,0.25 5.115,0.375 5.427,0.573 0.313,0.198 10 false e25 2.635,0.365 2.948,0.563 0.313,0.198 10 false e24 1.583,0.375 1.896,0.573 0.313,0.198 10 false e23

a.

Disconnect the e23 and e25 position control ECU assembly (driver seat) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Terminal Description Condition Specified Condition
e23-3 (+B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
e25-1 (IG) - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
e25-15 (SYSB) - Body ground System power source Ignition switch off*1
Always*2
11 to 14 V
e23-2 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the e23 and e25 position control ECU assembly (driver seat) connectors.


d.

Measure the voltage and resistance according to the value (s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
e23-1 (SLD+) - Body ground Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
e23-5 (SLD-) - Body ground Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
e23-6 (LFT+) - Body ground Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch on (Upward) 11 to 14 V
e24-5 (LFT-) - Body ground Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch on (Downward) 11 to 14 V
e23-10 (RCL+) - Body ground Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
e24-6 (RCL-) - Body ground Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
e23-7 (FRV+) - Body ground Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
e24-4 (FRV-) - Body ground Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
e23-9 (L+) - Body ground Lumbar support adjuster motor signal (forward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Forward) 11 to 14 V
e24-3 (L-) - Body ground Lumbar support adjuster motor signal (rearward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Rearward) 11 to 14 V
e25-4 (LFLF) - Body ground Front power seat switch (driver seat) (lumbar support adjuster switch (forward)) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Forward) Below 1 V
e25-18 (LFLR) - Body ground Front power seat switch (driver seat) (lumbar support adjuster switch (rearward)) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Rearward) Below 1 Ω
e25-9 (SLDF) - Body ground Front power seat switch (driver seat) (slide switch (forward)) signal Slide switch off 11 to 14 V
Slide switch on (Forward) Below 1 V
e25-23 (SLDR) - Body ground Front power seat switch (driver seat) (slide switch (rearward)) signal Slide switch off 11 to 14 V
Slide switch on (Rearward) Below 1 V
e25-8 (RCLF) - Body ground Front power seat switch (driver seat) (reclining switch (forward)) signal Reclining switch off 11 to 14 V
Reclining switch on (Forward) Below 1 V
e25-22 (RCLR) - Body ground Front power seat switch (driver seat) (reclining switch (rearward)) signal Reclining switch off 11 to 14 V
Reclining switch on (Rearward) Below 1 V
e25-6 (FRVU) - Body ground Front power seat switch (driver seat) (front vertical switch (upward)) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Upward) Below 1 V
e25-20 (FRVD) - Body ground Front power seat switch (driver seat) (front vertical switch (downward)) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Downward) Below 1 V
e25-7 (LFTU) - Body ground Front power seat switch (driver seat) (lifter switch (upward)) signal Lifter switch off 11 to 14 V
Lifter switch on (Upward) Below 1 V
e25-21 (LFTD) - Body ground Front power seat switch (driver seat) (lifter switch (downward)) signal Lifter switch off 11 to 14 V
Lifter switch on (Downward) Below 1 V
e25-12 (SGND) - Body ground Sensor ground Always Below 1 Ω


e.

Check for pulses according to the value (s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
e25-10 (SSFV) - Body ground Front vertical position signal Front vertical function operating 4.8 to 5.1 V
e25-11 (SSRR) - Body ground Reclining position signal Reclining function operating 4.8 to 5.1 V
e25-25 (SSRL) - Body ground Lifter position signal Lifter function operating 4.8 to 5.1 V
e25-26 (SSRS) - Body ground Slide position signal Slide function operating 4.8 to 5.1 V



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)


B343031C60
4.125,0.083 4.542,0.333 0.417,0.25 2.073,0.083 2.49,0.333 0.417,0.25 2.76,0.083 3.177,0.333 0.417,0.25 4.781,0.083 5.198,0.333 0.417,0.25 4.229,0.125 4.74,0.344 0.51,0.219 10 false J23 2.188,0.115 2.698,0.333 0.51,0.219 10 false z17 2.531,0.115 3.042,0.333 0.51,0.219 10 false *A 4.583,0.115 5.094,0.333 0.51,0.219 10 false *A 2.844,0.115 3.354,0.333 0.51,0.219 10 false z16 3.24,0.115 3.75,0.333 0.51,0.219 10 false *B 4.927,0.125 5.438,0.344 0.51,0.219 10 false J7 5.25,0.115 5.76,0.333 0.51,0.219 10 false *B
*A for LHD *B for RHD


a.

for LHD

i.

Disconnect the J23 outer mirror control ECU assembly (driver door) connector.


ii.

Measure the voltage and resistance according to the value (s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Terminal Description Condition Specified Condition
J23-6 (CPUB) - J23-7 (GND) Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
J23-14 (BDR) - J23-7 (GND) Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
J23-5 (SIG) - J23-7 (GND) Ignition power supply Ignition switch ON 11 to 14 V
J23-5 (SIG) - J23-7 (GND) Ignition power supply Ignition switch off Below 1 V
J23-7 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



iii.

Reconnect the J23 outer mirror control ECU assembly (driver door) connector.


iv.

Measure the voltage according to the value (s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
J23-1 (MM) - J23-7 (GND) SET switch signal for seat memory switch (driver door) SET switch on Below 1 V
SET switch off 11 to 14 V
J23-2 (M1) - J23-7 (GND) M1 switch signal for seat memory switch (driver door) M1 switch on Below 1 V
M1 switch off 11 to 14 V
J23-3 (M2) - J23-7 (GND) M2 switch signal for seat memory switch (driver door) M2 switch on Below 1 V
M2 switch off 11 to 14 V



b.

for RHD

i.

Disconnect the J7 outer mirror control ECU assembly (driver door) connector.


ii.

Measure the voltage and resistance according to the value (s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Terminal Description Condition Specified Condition
J7-6 (CPUB) - J7-7 (GND) Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
J7-14 (BDR) - J7-7 (GND) Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
J7-5 (SIG) - J7-7 (GND) Ignition power supply Ignition switch ON 11 to 14 V
J7-5 (SIG) - J7-7 (GND) Ignition power supply Ignition switch off Below 1 V
J7-7 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



iii.

Reconnect the J7 outer mirror control ECU assembly (driver door) connector.


iv.

Measure the voltage according to the value (s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
J7-1 (MM) - J7-7 (GND) SET switch signal for seat memory switch (driver door) SET switch on Below 1 V
SET switch off 11 to 14 V
J7-2 (M1) - J7-7 (GND) M1 switch signal for seat memory switch (driver door) M1 switch on Below 1 V
M1 switch off 11 to 14 V
J7-3 (M2) - J7-7 (GND) M2 switch signal for seat memory switch (driver door) M2 switch on Below 1 V
M2 switch off 11 to 14 V




CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B520311N42
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.385,4.573 5.823,4.823 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.292,6.198 5.729,6.448 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 3.469,7.677 3.781,7.875 0.313,0.198 10 false MB 4.292,0.219 4.604,0.417 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false H42 2.042,1.479 2.354,1.677 0.313,0.198 10 false H43 2.042,1.802 2.354,2 0.313,0.198 10 false H44 0.865,1.073 1.177,1.271 0.313,0.198 10 false 4D 0.865,1.656 1.177,1.854 0.313,0.198 10 false 4C 0.875,2.021 1.188,2.219 0.313,0.198 10 false 4E 0.896,2.25 1.208,2.448 0.313,0.198 10 false 4F 5.844,1.146 6.156,1.344 0.313,0.198 10 false 4B 5.844,1.76 6.156,1.958 0.313,0.198 10 false 4A 1.229,3.281 1.542,3.479 0.313,0.198 10 false H44 3.25,3.25 3.563,3.448 0.313,0.198 10 false H43 5.531,3.24 5.844,3.438 0.313,0.198 10 false H42 1.833,4.604 2.146,4.802 0.313,0.198 10 false 4A 1.24,6.198 1.552,6.396 0.313,0.198 10 false 4C 3.813,6.156 4.125,6.354 0.313,0.198 10 false 4D 5.427,6.219 5.74,6.417 0.313,0.198 10 false 4F 6.448,6.229 6.76,6.427 0.313,0.198 10 false 4E 5.51,4.604 5.823,4.802 0.313,0.198 10 false 4B


b.

Measure the voltage and resistance according to the value (s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Terminal Description Condition Specified Condition
MB-31 (BECU) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
MB-32 (IG) - Body ground Ignition power supply Ignition switch ON 11 to 14 V
MB-32 (IG) - Body ground Ignition power supply Ignition switch off Below 1 V
MB-30 (ACC) - Body ground Ignition power supply Ignition switch ACC 11 to 14 V
MB-30 (ACC) - Body ground Ignition power supply Ignition switch off Below 1 V
MB-11 (GND1) - Body ground Ground Always Below 1 Ω
H43-1 (FLCY) - Body ground*3 Front door courtesy light switch assembly (driver door) input Front door (driver door) closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω
H43-6 (FRCY) - Body ground*4 Front door courtesy light switch assembly (driver door) input Front door (driver door) closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω

*1: for HV Model

*2: for Gasoline Model

*3: for LHD

*4: for RHD