CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
| *a | This connector is not used by the seat heater system. Refer to Air Conditioning System. | - | - |
Disconnect the H62 air conditioning amplifier assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H62-6 (IG+) - H62-17 (GND) | IG power supply | Ignition switch off | Below 1 V |
| H62-6 (IG+) - H62-17 (GND) | IG power supply | Ignition switch ON | 11 to 14 V |
| H62-5 (B) - H62-17 (GND) | Auxiliary battery power supply | Ignition switch off*1
Always*2 |
11 to 14 V |
| H62-17 (GND) - Body ground | Ground | Always | Below 1 Ω |
*1: for HV Model
*2: for Gasoline Model
Reconnect the H62 air conditioning amplifier assembly connector.
Measure the voltage and check for pulses generation according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H64-12 (SM1R) - H62-17 (GND) | Front seat heater control signal | ·
Ignition switch ON ·
Front seat heater switch (air conditioning control assembly) on (LO) (heater position) |
Below 1 V |
| H64-13 (SM1L) - H62-17 (GND) | Front seat heater control signal | ·
Ignition switch ON ·
Front seat heater switch (air conditioning control assembly) on (LO) (heater position) |
Below 1 V |
| H64-23 (SM2R) - H62-17 (GND) | Rear seat heater control signal | ·
Ignition switch ON ·
Rear seat heater switch (Air conditioning control assembly No. 2) (RH) on |
Below 1 V |
| H64-24 (SM2L) - H62-17 (GND) | Rear seat heater control signal | ·
Ignition switch ON ·
Rear seat heater switch (Air conditioning control assembly No. 2) (LH) on |
Below 1 V |
| H62-7 (LIN1) - Body ground | Seat heater switch signal | Ignition switch ON | Pulse generation |
CHECK FRONT SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY)
Disconnect the H27 front seat heater switch (air conditioning control assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H27-4 (IG+) - H27-8 (GND)*1 | IG power supply | Ignition switch off | Below 1 V |
| H27-6 (IG+) - H27-10 (GND)*2 | |||
| H27-4 (IG+) - H27-8 (GND)*1 | IG power supply | Ignition switch ON | 11 to 14 V |
| H27-6 (IG+) - H27-10 (GND)*2 | |||
| H27-8 (GND) - Body ground*1 | Ground | Always | Below 1 Ω |
| H27-10 (GND) - Body ground*2 |
*1: for 12.3 Inch Display
*2: for 8 Inch Display
Reconnect the H27 front seat heater switch (air conditioning control assembly) connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H27-3 (LIN1) - H27-8 (GND)*1 | Front seat heater switch signal | Ignition switch ON | Pulse generation |
| H27-8 (LIN1) - H27-10 (GND)*2 |
*1: for 12.3 Inch Display
*2: for 8 Inch Display
CHECK REAR SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY NO. 2)
for HV Model: Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>TERMINALS OF ECU
for Gasoline Model: Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model with Automatic Air Conditioning System)>TERMINALS OF ECU