Refer to DTC C050612.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C050623 | Right Front Wheel Speed Sensor Signal Stuck Low | Any of the following is detected:
·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.*2 ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more.*1 ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more. ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.*2 ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 30 seconds or more.*1 |
·
Speed sensor installation ·
Wire harness and connector ·
Front speed sensor RH ·
Front speed sensor rotor RH (front axle hub sub-assembly RH) |
*1: for AWD
*2: for 2WD
Refer to DTC C050612.
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
| *1 | Front Speed Sensor RH |
| *a | Correct |
| *b | Incorrect |
| *c | 8.5 N*m (87 kgf*cm, 75 in.*lbf) |
| *d | No clearance |
Check the front speed sensor RH installation.
There is no clearance between the front speed sensor RH and front steering knuckle RH.
The installation bolt is tightened properly.
8.5 N*m (87 kgf*cm, 75 in.*lbf)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front speed sensor RH.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
Check the front speed sensor tip RH.
The front speed sensor tip RH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the front speed sensor RH, clean the front speed sensor RH.
If the front speed sensor RH is damaged, replace the front speed sensor RH with a new one.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Start the engine.
Perform a road test.
Check the front speed sensor RH output value.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
The output value changes in accordance with the vehicle speed.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the A40 front speed sensor RH connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-1 (FR+) - A39-7 (FR+) | Always | Below 1 Ω |
| A40-1 (FR+) or A39-7 (FR+) - Body ground | Always | 10 kΩ or higher |
| A40-2 (FR-) - A39-6 (FR-) | Always | Below 1 Ω |
| A40-2 (FR-) or A39-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the component with the front speed sensor rotor RH.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL
Check the front speed sensor rotor RH.
The front speed sensor rotor RH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the front speed sensor rotor RH, clean the front speed sensor rotor RH.
Do not use parts cleaner when cleaning the front speed sensor rotor RH.
If the front speed sensor rotor RH is damaged, replace the front speed sensor rotor RH with a new one.
The front speed sensor rotor RH is incorporated into the front axle hub sub-assembly RH.
If the front speed sensor rotor RH needs to be replaced, replace it together with the front axle hub sub-assembly RH.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The front speed sensor rotor RH is damaged.) | B |
| NG (There is foreign matter on the front speed sensor rotor RH.) | C |
A
B
C