Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C050612  Right Front Wheel Speed Sensor Circuit Short to Battery  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C235852E10
1.073,0.865 1.448,0.865 1.448,0.865 1.448,1.073 false 6.458,0.979 6.958,1.146 0.5,0.167 10 false 1.4 V 6.458,1.323 6.969,1.479 0.51,0.156 10 false 0.7 V 0.146,0.771 1.167,1.104 1.021,0.333 10 false Speed Sensor 4.469,1.792 5.396,2.021 0.927,0.229 10 false Low speed 5.375,1.792 6.49,2.104 1.115,0.313 10 false High speed 1.115,2.125 2.74,2.479 1.625,0.354 10 false Speed Sensor Rotor

DTC No. Detection Item DTC Detection Condition Trouble Area
C050612 Right Front Wheel Speed Sensor Circuit Short to Battery The speed sensor short signal is ON continuously for 0.5 seconds or more.
·

Front speed sensor RH

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C400496E27
5.302,1.302 5.802,1.469 0.5,0.167 10 false FR+ 1.667,1.167 2.104,1.333 0.438,0.167 10 false FR+ 1.667,1.833 2.104,2.021 0.438,0.188 10 false FR- 5.302,1.979 5.76,2.177 0.458,0.198 10 false FR- 4.917,2.969 5.417,3.167 0.5,0.198 10 false A39 4.917,3.125 7.073,3.615 2.156,0.49 10 false Skid Control ECU (Brake Actuator Assembly) 5.031,1.031 5.365,1.281 0.333,0.25 10 false 7 5.031,1.708 5.344,2.021 0.313,0.313 10 false 6 2.021,1.688 2.406,1.958 0.385,0.271 10 false 2 2.021,1.021 2.375,1.292 0.354,0.271 10 false 1 0.75,2.417 2.417,2.667 1.667,0.25 10 false Front Speed Sensor RH 0.75,2.25 1.219,2.448 0.469,0.198 10 false A40

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.
C375627C69
0.615,0.677 1.031,0.927 0.417,0.25 2.208,1.313 1.875,0.813 true 1.24,1.313 1.573,0.813 true 0.698,0.719 1.156,0.917 0.458,0.198 10 false A40 2.219,1.323 2.719,1.573 0.5,0.25 10 false FR+ 0.146,0.135 0.521,0.427 0.375,0.292 10 false *a 1.052,1.333 1.552,1.531 0.5,0.198 10 false FR-
*a Front view of wire harness connector
(to Front Speed Sensor RH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A40 front speed sensor RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-1 (FR+) - A40-2 (FR-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.
C375627C70
0.594,0.667 1.01,0.917 0.417,0.25 1.219,1.323 1.552,0.823 true 0.677,0.708 1.135,0.906 0.458,0.198 10 false A40 0.146,0.135 0.521,0.427 0.375,0.292 10 false *a 1.063,1.344 1.563,1.542 0.5,0.198 10 false FR-
*a Front view of wire harness connector
(to Front Speed Sensor RH)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-2 (FR-) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR RH - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR RH - BRAKE ACTUATOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-1 (FR+) or A39-7 (FR+) - A40-2 (FR-) or A39-6 (FR-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR