Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C051223  Right Rear Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTC C051212.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>C051212

DTC No. Detection Item DTC Detection Condition Trouble Area
C051223 Right Rear Wheel Speed Sensor Signal Stuck Low Any of the following is detected:
·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.*2

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more.*1

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 15 seconds or more.*2

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 30 seconds or more.*1


·

Rear skid control sensor RH*1

·

Rear speed sensor RH (rear axle hub and bearing assembly RH)*2

·

Speed sensor installation

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)

·

Wire harness and connector

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)



*1: for AWD

*2: for 2WD


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.


Result:
Result Proceed to
for AWD A
for 2WD B



A

2.CHECK REAR SKID CONTROL SENSOR RH INSTALLATION

B

8.CHECK REAR SPEED SENSOR RH INSTALLATION
2.CHECK REAR SKID CONTROL SENSOR RH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Rear Skid Control Sensor RH
*a Correct
*b Incorrect
*c 8.5 N*m (87 kgf*cm, 75 in.*lbf)
*d No clearance


Check the rear skid control sensor RH installation.

OK:

There is no clearance between the rear skid control sensor RH and the rear axle carrier RH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

3.CHECK REAR SKID CONTROL SENSOR RH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE REAR SKID CONTROL SENSOR RH

3.CHECK REAR SKID CONTROL SENSOR RH (CHECK FOR FOREIGN MATTER)

b.

Check the rear skid control sensor tip RH.

OK:

The rear skid control sensor tip RH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear skid control sensor RH, clean the rear skid control sensor RH.

·

If the rear skid control sensor RH is damaged, replace the rear skid control sensor RH with a new one.




Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (RR WHEEL SPEED)

NG

CLEAN OR REPLACE REAR SKID CONTROL SENSOR RH

4.READ VALUE USING GTS (RR WHEEL SPEED)
a.

Start the engine.


b.

Perform a road test.


c.

Check the rear skid control sensor RH output value.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RR Wheel Speed
50003 435 15
OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
5.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
a.
C418961C02
0.521,0.167 0.938,0.417 0.417,0.25 2.458,0.167 2.875,0.417 0.417,0.25 2.344,1.719 2.573,1.354 true 0.333,1.75 0.552,1.167 true 3.01,1.729 2.781,1.344 true 1.01,1.75 0.813,1.167 true 0.083,0.083 0.417,0.333 0.333,0.25 10 false *a 0.979,0.208 1.313,0.458 0.333,0.25 10 false *b 2.906,0.208 3.073,0.625 0.167,0.417 10 false *c 0.656,0.208 0.99,0.458 0.333,0.25 10 false u3 2.542,0.208 2.875,0.458 0.333,0.25 10 false uM1 0.25,1.75 0.583,2 0.333,0.25 10 false + 1.052,1.75 1.385,2 0.333,0.25 10 false - 2.188,1.74 2.521,1.99 0.333,0.25 10 false RR+ 3.01,1.75 3.313,2.083 0.302,0.333 10 false RR-
*a Front view of skid control sensor wire RH (No. 1 parking brake wire assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the u3 and uM1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
u3-1 (+) - uM1-3 (RR+) Always Below 1 Ω
u3-1 (+) or uM1-3 (RR+) - Body ground and other terminals Always 10 kΩ or higher
u3-2 (-) - uM1-4 (RR-) Always Below 1 Ω
u3-2 (-) or uM1-4 (RR-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
uM1-3 (RR+) - A39-20 (RR+) Always Below 1 Ω
uM1-3 (RR+) or A39-20 (RR+) - Body ground Always 10 kΩ or higher
uM1-4 (RR-) - A39-19 (RR-) Always Below 1 Ω
uM1-4 (RR-) or A39-19 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK REAR SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK REAR SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)
a.

Remove the component with the rear speed sensor rotor RH.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for 4WD/AWD)>REMOVAL


b.

Check the rear speed sensor rotor RH.

OK:

The rear speed sensor rotor RH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear speed sensor rotor RH, clean the rear speed sensor rotor RH.

·

Do not use parts cleaner when cleaning the rear speed sensor rotor RH.

·

If the rear speed sensor rotor RH is damaged, replace the rear speed sensor rotor RH with a new one.



HINT:
·

The rear speed sensor rotor RH is incorporated into the rear axle hub and bearing assembly RH.

·

If the rear speed sensor rotor RH needs to be replaced, replace it together with the rear axle hub and bearing assembly RH.




Result:
Result Proceed to
OK A
NG (The rear speed sensor rotor RH is damaged.) B
NG (There is foreign matter on the rear speed sensor rotor RH.) C



A

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

C

CLEAN REAR SPEED SENSOR ROTOR RH

8.CHECK REAR SPEED SENSOR RH INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor RH
*a Correct
*b Incorrect
*c No clearance


Check the rear speed sensor RH installation.

OK:

There is no clearance between the rear speed sensor RH and the rear axle hub and bearing assembly RH.


HINT:

Because the rear axle hub and bearing assembly RH cannot be disassembled, if the rear speed sensor RH needs replacement, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (RR WHEEL SPEED)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

9.READ VALUE USING GTS (RR WHEEL SPEED)
a.

Start the engine.


b.

Perform a road test.


c.

Check the rear speed sensor RH output value.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RR Wheel Speed
50003 435 15
OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

10.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
10.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
a.
C418961C08
0.521,0.167 0.938,0.417 0.417,0.25 2.458,0.167 2.875,0.417 0.417,0.25 2.344,1.719 2.573,1.354 true 0.333,1.75 0.552,1.167 true 3.01,1.729 2.781,1.344 true 1.01,1.75 0.813,1.167 true 0.083,0.083 0.417,0.333 0.333,0.25 10 false *a 0.979,0.208 1.313,0.458 0.333,0.25 10 false *b 2.906,0.208 3.073,0.625 0.167,0.417 10 false *c 0.656,0.208 0.99,0.458 0.333,0.25 10 false u3 2.542,0.208 2.875,0.458 0.333,0.25 10 false uM1 0.25,1.75 0.583,2 0.333,0.25 10 false - 1.052,1.75 1.385,2 0.333,0.25 10 false + 2.188,1.74 2.521,1.99 0.333,0.25 10 false RR+ 3.01,1.75 3.313,2.083 0.302,0.333 10 false RR-
*a Front view of skid control sensor wire RH (No. 1 parking brake wire assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the u3 and uM1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
u3-2 (+) - uM1-3 (RR+) Always Below 1 Ω
u3-2 (+) or uM1-3 (RR+) - Body ground and other terminals Always 10 kΩ or higher
u3-1 (-) - uM1-4 (RR-) Always Below 1 Ω
u3-1 (-) or uM1-4 (RR-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
uM1-3 (RR+) - A39-20 (RR+) Always Below 1 Ω
uM1-3 (RR+) or A39-20 (RR+) - Body ground Always 10 kΩ or higher
uM1-4 (RR-) - A39-19 (RR-) Always Below 1 Ω
uM1-4 (RR-) or A39-19 (RR-) - Body ground Always 10 kΩ or higher


HINT:
·

The rear speed sensor RH is incorporated into the rear axle hub and bearing assembly RH.

·

If the rear speed sensor RH needs to be replaced, replace the rear axle hub and bearing assembly RH.




Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR