Home › General › MAINTENANCE › FRONT BRAKE FLEXIBLE HOSE › from 2020.11
RM37A0E _V1 General _086848 MAINTENANCE _0420826 FRONT BRAKE FLEXIBLE HOSE A

MAINTENANCE  FRONT BRAKE FLEXIBLE HOSE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Because the left and right front flexible hoses are not interchangeable, verify the part number when installing the front flexible hoses.

·

When reusing the front flexible hoses, use the identification marks created during removal to install each front flexible hose to its original position.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 47313J 1.INSTALL FRONT FLEXIBLE HOSE

NOTICE:

When installing the front flexible hose, minimize twisting of the hose.


a.
C423887C02
0.552,0.365 0.635,0.365 0.635,0.365 0.688,0.781 false 1.427,0.26 1.74,0.417 0.313,0.156 10 false *a 0.406,0.271 0.719,0.427 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Install the front flexible hose with a new clip.

NOTICE:

Install the clip as far as it will go.



b.

Using a union nut wrench, connect the brake line to the front flexible hose while holding the front flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




c.
C423888C01
0,0 0,0 false
V100135

Hook


Engage the 2 hooks to install the front speed sensor clamp bracket.

NOTICE:

Do not twist the front speed sensor wire harness when installing it.



d.
C423885

Install the front flexible hose and front speed sensor to the front shock absorber assembly with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Do not twist the front flexible hose when installing it.



e.

Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Install the front flexible hose lock securely into the lock hole in the front disc brake cylinder assembly.

·

Do not twist the front flexible hose when installing it.




Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

a.

Connect the reservoir level switch connector.


b.

for LHD:

i.

Install the brake master cylinder reservoir assembly to the reservoir bracket with the bolt and nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


ii.

Engage the clamp to install the wire harness to the brake master cylinder reservoir assembly.



c.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION


Hide 4.INSTALL FRONT WHEEL