Home › General › MAINTENANCE › REAR DISC BRAKE PAD › from 2020.11
RM37A0E _V1 General _086848 MAINTENANCE _0420827 REAR DISC BRAKE PAD A

MAINTENANCE  REAR DISC BRAKE PAD  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure. (for HV Model)

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 04946 1.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

NOTICE:
·

When replacing worn rear disc brake pads, the rear disc brake anti-squeal shims and rear disc brake pad wear indicator plates must be replaced together with the rear disc brake pads.

·

Install each rear disc brake pad wear indicator plate in the correct position and direction.

·

Install the rear disc brake anti-squeal shims in the correct positions and directions.



a.

Check the rear disc brake pad.

HINT:
C423913C01
0.292,0.115 0.604,0.271 0.313,0.156 10 false *a 0.292,1.865 0.604,2.021 0.313,0.156 10 false *b
*a Inner Side
*b Outer Side


Use the illustration to identify the inner side rear disc brake pad and outer side rear disc brake pad so that they can be installed to the correct side of the caliper.



b.
C423922C02
0.365,1.146 0.365,1.719 false 0.875,1.427 0.875,2.042 false 1.51,2.385 1.51,2.604 false 2.073,2.729 2.073,2.948 false 2.969,1.625 2.969,2.188 false 2.531,1.333 2.531,1.865 false 0.802,2.115 1.052,2.271 0.25,0.156 10 false *1 0.302,1.76 0.615,1.917 0.313,0.156 10 false *2 2.479,1.094 2.729,1.25 0.25,0.156 10 false *1 2.906,1.365 3.219,1.521 0.313,0.156 10 false *2 1.438,2.667 1.615,2.833 0.177,0.167 10 false *3 2.021,3.01 2.198,3.188 0.177,0.177 10 false *3
*1 Rear No. 1 Disc Brake Anti-squeal Shim
*2 Rear No. 2 Disc Brake Anti-squeal Shim
*3 Rear Disc Brake Pad Wear Indicator Plate


Install the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim to each rear disc brake pad.


c.

Install a new rear disc brake pad wear indicator plate to each rear disc brake pad.


Hide 04466 2.INSTALL REAR DISC BRAKE PAD

CAUTION:

Be careful not to get pinched by the rear disc brake cylinder assembly or other parts when installing the rear disc brake pads.


a.

Push in the rear disc brake piston.

NOTICE:
·

Make sure the brake fluid does not overflow from the reservoir.

·

Do not forcibly push in the rear disc brake piston.




b.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:
·

Keep the friction surfaces of the rear disc brake pads and rear disc free from oil and grease.

·

Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the lower side of the vehicle.




Hide 3.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.

Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with 2 new bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


b.

Depress the brake pedal several times. (for Gasoline Model)


Hide 4.INSTALL FLEXIBLE HOSE

a.
C423925

Install the rear flexible hose to the No. 2 flexible hose bracket with the 2 bolts.

Torque:
18.8 N*m (192 kgf*cm, 14 ft.*lbf)


Hide 890C0A 5.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 6.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

a.

Connect the reservoir level switch connector.


b.

for LHD:

i.

Install the brake master cylinder reservoir assembly to the reservoir bracket with the bolt and nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


ii.

Engage the clamp to install the wire harness to the brake master cylinder reservoir assembly.



c.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION


d.

Turn the ignition switch to ON (READY).


e.

Depress the brake pedal and release it.



Hide 8.INSTALL REAR WHEEL