Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › GRILLE SHUTTER SYSTEM › from 2021.10
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0457335 GRILLE SHUTTER SYSTEM J

EXTERIOR PANELS / TRIM  GRILLE SHUTTER SYSTEM  Grille Shutter does not Operate  


DESCRIPTION

The grille shutter of the radiator shutter sub-assembly may not operate when dirty due to foreign matter, snow, mud, etc., or the power supply voltage deteriorates.

WIRING DIAGRAM

B589971E13
5.823,1.677 7.125,2.094 1.302,0.417 10 false Swing Grille Actuator Assembly 4.281,0.635 5.583,1.052 1.302,0.417 10 false GRILLE SHUTTER 3.26,1.146 4.563,1.563 1.302,0.417 10 false EFI-MAIN NO. 1 1.917,0.635 3.219,1.052 1.302,0.417 10 false EFI-MAIN NO. 1 0.115,0.479 1.792,0.958 1.677,0.479 10 false from Auxiliary Battery 5.844,1.51 6.583,1.865 0.74,0.354 10 false X1 6.188,0.5 6.604,0.844 0.417,0.344 10 false +B 6.188,1.125 6.604,1.469 0.417,0.344 10 false GND 5.99,0.385 6.406,0.729 0.417,0.344 10 false 1 6,1.01 6.417,1.354 0.417,0.344 10 false 3 2.594,1.49 4.844,1.875 2.25,0.385 10 false No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly 4.083,0.396 4.5,0.74 0.417,0.344 10 false 5 3.333,0.396 3.75,0.74 0.417,0.344 10 false 3 3.323,0.771 3.74,1.115 0.417,0.344 10 false 1 4.083,0.781 4.5,1.125 0.417,0.344 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, change the grille shutter control mode to maintenance mode.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

If the radiator shutter assembly has been replaced with a new one, perform initialization and change the grille shutter control mode.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM UTILITY USING GTS (SWITCH GRILLE SHUTTER CONTROL MODE)
a.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 4672

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR GRILLE SHUTTER (FOREIGN MATTER AND ICE)
2.CHECK FOR GRILLE SHUTTER (FOREIGN MATTER AND ICE)
a.

Check the area around the shutters and the links of the grille shutter for foreign matter and ice.

OK:

The radiator shutter sub-assembly is free of foreign matter and ice.



Result:
Proceed to
OK
NG



OK

3.CHECK RADIATOR SHUTTER ASSEMBLY (GRILLE SHUTTER OPERATION)

NG

10.REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)
3.CHECK RADIATOR SHUTTER ASSEMBLY (GRILLE SHUTTER OPERATION)
a.

Remove the radiator shutter assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>REMOVAL


b.

While using fingers to pinch the fin at the location shown in the illustration, fully open and close the radiator shutter assembly manually and check that it moves smoothly.

HINT:

If the fin is pinched with fingers far from the swing grille actuator assembly, the function may not be able to be inspected correctly.


B597731C01
1.906,2.51 2.094,2.51 2.094,2.51 2.365,1.698 true 5.25,2.021 5.021,2.021 5.021,2.021 4.552,1.24 true 1.74,2.417 2.052,2.573 0.313,0.156 10 false *a 5.302,1.948 5.615,2.104 0.313,0.156 10 false *b
*a Swing Grille Actuator Assembly *b Fin


OK:

Radiator shutter sub-assembly moves smoothly.



c.

Install the radiator shutter assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>INSTALLATION


Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPLACE RADIATOR SHUTTER ASSEMBLY

4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC
5.CHECK DTC
a.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output. OK
DTCs are output. NG



OK

6.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - POWER SUPPLY AND BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - POWER SUPPLY AND BODY GROUND)
a.
B589982C13
0.5,1.458 0.917,1.708 0.417,0.25 0.719,1.094 0.896,1.094 0.896,1.094 1.427,1.583 true 2.76,1.083 2.563,1.083 2.563,1.083 1.979,1.583 true 0.594,1.5 1.198,1.885 0.604,0.385 10 false X1 0.51,1.021 0.969,1.219 0.458,0.198 10 false +B 2.813,1.01 3.271,1.208 0.458,0.198 10 false GND 0.125,0.115 0.438,0.271 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Disconnect the X1 swing grille actuator assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X1-1 (+B) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-3 (GND) - Body ground Always Below 1 Ω



d.

Connect the X1 swing grille actuator assembly connector.


Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)

NG

8.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - EFI-MAIN NO. 1 RELAY)
7.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
a.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 4672

b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Grille Shutter Control Mode Grille shutter control mode status Normal or Maintenance Normal: Normal mode
Maintenance: Maintenance mode
-
Powertrain > Engine > Data List
Tester Display
Grille Shutter Control Mode
50003 372 1304
OK:

Normal is displayed.



Result:
Proceed to
NEXT



NEXT

END
HINT:

Operation temporarily abnormal due to fail-safe (abnormal temperature).



8.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - EFI-MAIN NO. 1 RELAY)
a.
B340809C30
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
(EFI-MAIN NO. 1 Relay Holder)


Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the X1 swing grille actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (+B) - No. 1 engine room relay block and No. 1 junction block assembly EFI-MAIN NO. 1 relay terminal 5 Always Below 1 Ω
X1-1 (+B) or No. 1 engine room relay block and No. 1 junction block assembly EFI-MAIN NO. 1 relay terminal 5 - Body ground Always 10 kΩ or higher



d.

Install the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


e.

Connect the X1 swing grille actuator assembly connector.


Result:
Proceed to
OK
NG



OK

9.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

7.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
10.REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)
a.

Remove any foreign matter and/or ice from the area around the shutters and the links of the grille shutter.


Result:
Proceed to
NEXT



NEXT

7.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)