Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD) › from 2021.10
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420996 MOTOR GENERATOR CONTROL SYSTEM(for 4WD/AWD) C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for 4WD/AWD)  P1CCC96  DC/DC Converter Enable Component Internal Failure  


DESCRIPTION

The DC/DC converter converts the DC 288 V of the HV battery into DC 12 V in order to supply power to areas such as the vehicle lighting system, audio system and various ECUs. Additionally, it charges the auxiliary battery.

A transistor bridge circuit initially converts DC 288 V into alternating current, and a transformer lowers the voltage.

The DC/DC converter controls the output voltage in order to keep a constant voltage at the terminals of the auxiliary battery.

Then, it is rectified and smoothed (into direct current) and converted into DC 12 V.

The motor generator control ECU sends a signal to the DC/DC converter to prohibit its control and receives signals indicating a normal or abnormal condition of the 12 V charging system via the NODD signal line.

If the DC/DC converter malfunctions, the vehicle will become inoperative. Therefore, the motor generator control ECU monitors the operation of the DC/DC converter and detects malfunctions.

This DTC is stored when the DC/DC converter circuit has a malfunction or its operation is prohibited by a fail-safe function, or the auxiliary battery voltage drops to 11 V or less with the ignition switch ON (READY).

If a DC/DC converter malfunction occurs, DC/DC converter malfunction signals are sent from the DC/DC converter to the MG ECU via the NODD signal line.

This DTC may also be stored if a malfunction of the inverter cooling system (blockage, inverter water pump malfunction, etc.) or a high-voltage insulation malfunction occurs.

A369836E21
5.24,0.313 6.156,0.51 0.917,0.198 10 false DC 288 V 0.229,3.917 1.844,4.125 1.615,0.208 10 false from Auxiliary Battery 1.073,3.625 2.531,3.833 1.458,0.208 10 false from IGCT NO. 3 Fuse 3.302,4.125 5.156,4.365 1.854,0.24 10 false Hybrid Vehicle Control ECU 4.302,3.479 6.615,3.74 2.313,0.26 10 false Inverter with Converter Assembly 2.438,2.438 3.635,2.688 1.198,0.25 10 false DC/DC Converter 3.271,2.875 5.292,3.115 2.021,0.24 10 false Motor Generator Control ECU 0.969,0.969 1.74,1.167 0.771,0.198 10 false DC/DC 2.031,0.917 2.49,1.115 0.458,0.198 10 false AMD 4.104,2.188 4.719,2.385 0.615,0.198 10 false NODD 4.615,2.188 5.073,2.385 0.458,0.198 10 false VLO

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1CCC96 DC/DC Converter Enable Component Internal Failure Both of the following conditions are met:
·

The DC/DC converter is malfunctioning and the auxiliary battery voltage is 11 V or less.*

·

The inverter coolant temperature is 70°C (158°F) or lower for 5 seconds.


(1 trip detection logic)
·

Fusible link block assembly

·

Engine wire

·

Inverter cooling system

·

Cooling fan system

·

Grille shutter system

·

Inverter with converter assembly

·

Motor cable

·

HV floor under wire (rear traction motor cable)

·

Hybrid vehicle transaxle assembly

·

Rear traction motor with transaxle assembly


Does not come on Master Warning:
Comes on

HINT:

*: If the DC/DC converter is malfunctioning, its operation and charging will be stopped and the auxiliary battery voltage will drop.


WIRING DIAGRAM

Refer to the wiring diagram for the Generator High-voltage Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Generator High-voltage Circuit

Refer to the wiring diagram for the Motor High-voltage Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Motor High-voltage Circuit

Refer to the wiring diagram for the Rear Motor High-voltage Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Rear Motor High-voltage Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


HINT:
·

After repair, clear the DTCs, turn the ignition switch off and wait for 30 seconds or more and perform the following procedure to confirm that the auxiliary battery low voltage indicated by this DTC has been repaired.

(a)

Wait for 2 minutes with the shift lever in P, the ignition switch ON (READY) and the following conditions met, then confirm that Data List item "BATT Voltage (Hybrid control system)" is between 13.0 and 15.0 V.

(If charging is not performed and the electrical load increases, +B voltage may not be steady and will gradually drop.)

(1)

Headlight switch is in the HI position.

(2)

A/C blower fan switch is in the HI position.

(3)

Window defogger switch is turned on.



·

By performing the following procedure, the DC/DC converter function can be checked.

(a)

Connect the AC/DC 400 A probe to the positive (+) auxiliary battery cable.

(1)

Turn the ignition switch to ON (READY) and leave the vehicle as is until the electric current flowing to the auxiliary battery becomes 10 A or less.

(2)

Turn the ignition switch to ON (READY) and turn the headlight switch and A/C blower fan switch to the HI position and the window defogger on.

(3)

Confirm that the current drawn from the auxiliary battery is 0 A or lower and the auxiliary battery voltage is between 12.5 and 15.0 V.




·

This DTC may be also stored when a part other than the DC/DC converter is malfunctioning or depending on user operation.


·

If this vehicle is used to jump start another vehicle with a discharged battery, a fuse may blow due to overcurrent or the DC/DC converter self-protection may be activated. Also, if this vehicle is jump started by a vehicle with a 24 V battery, the same malfunction may occur and this DTC may be stored. (The suspended DC/DC converter control will return to normal by clearing the DTCs and turning the ignition switch off.)


·

Check whether high electrical load equipment such as a high-capacitance audio device or electric kettle is used in the vehicle. (A fuse of the auxiliary battery may be blown due to overcurrent.)


·

If the DC/DC converter is malfunctioning, the auxiliary battery cannot be charged. Therefore, once the ignition switch is turned off, it may be impossible to turn it to ON (READY) again if the auxiliary battery is completely discharged. In this case, charge the auxiliary battery. Be careful as charging is not performed during the inspection.


·

If the ignition switch turns off immediately after it is turned to ON (READY), the auxiliary battery voltage may be low. Charge the auxiliary battery.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P1CCC96 only is output, or DTCs except the ones in the table below are also output A
DTCs of hybrid control system in the table below are output B
DTCs of motor generator control system in the table below are output C
DTCs of SFI system in the table below are output D


Table 1
Malfunction Content System Relevant DTC
Insulation Malfunction Hybrid control system P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure
P1C7D49 Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure
P1C7E49 Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure
P1C7F49 Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure
P1C8049 Hybrid/EV Battery Voltage System Isolation (Rear Motor Area) Internal Electronic Failure
High Voltage Circuit Malfunction Hybrid control system P0AA649 Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure
P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0AE411 Hybrid/EV Battery Precharge Contactor Circuit Short to Ground
P1C8449 High Voltage Power Resource Circuit Short during Ready ON
P300449 High Voltage Power Resource Circuit Short during Pre-Charge

Table 2
Malfunction Content System Relevant DTC
System malfunction Hybrid control system P0A9300 Inverter "A" Cooling System Performance
P0C7396 Motor Electronics Coolant Pump "A" Component Internal Failure
P314A31 Motor Electronics Coolant Pump "A" No Signal
Motor generator control system P0E5717 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold
SFI system P059A71 Active Grille Air Shutter "A" Actuator Stuck
P059A79 Active Grille Air Shutter "A" Mechanical Linkage Failure
P05A212 Active Grille Air Shutter "A" Circuit Short to Battery
P15AD87 Active Grille Air Shutter "A" Missing Message

HINT:

P1CCC96 may be output as a result of the malfunction indicated by the DTCs above.

1.

The chart above is listed in inspection order of priority.

2.

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)




b.

Turn the ignition switch off.



A

2.CHECK AMD TERMINAL CONNECTION CONDITION

B

C

D

2.CHECK AMD TERMINAL CONNECTION CONDITION
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A455450C01
0.698,2.552 0.854,1.229 0.854,1.229 1.083,1.229 true 2.031,0.25 2.208,0.25 2.208,0.25 2.854,0.927 true 1.156,1.135 1.406,1.333 0.25,0.198 10 true *1 1.76,0.156 2,0.354 0.24,0.198 10 true *2
*1 AMD Terminal
(Inverter with Converter Assembly Side)
*2 AMD Terminal
(No. 1 Engine Room Relay Block and Junction Block Assembly Side)


Check that the nuts for the AMD terminal are tightened to the specified torque, the AMD terminal is connected securely, and there are no contact problems.

Torque:
Inverter with converter assembly side:

T=10 N*m (102 kgf*cm, 7 ft.*lbf)

No. 1 engine room relay block and junction block assembly side:

T=8.0 N*m (82 kgf*cm, 71 in.*lbf)


Result:
Result Proceed to
There are no arc marks. The terminal is connected securely and there are no contact problems. A
There are no arc marks. The terminal is not connected securely and there is a contact problem. B
There are arc marks. - C




A

3.CHECK AMD TERMINAL VOLTAGE

B

CONNECT SECURELY

C

REPLACE MALFUNCTIONING PARTS

3.CHECK AMD TERMINAL VOLTAGE
CAUTION:

Be sure to wear insulated gloves.


a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.
A455451E01
1.896,0.76 2.313,1.042 0.417,0.281 1.99,0.802 2.229,0.99 0.24,0.188 10 true 1E

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1E-1 - Body ground Ignition switch off Same as auxiliary battery voltage



c.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE WIRE

NG

7.CHECK FUSIBLE LINK BLOCK ASSEMBLY (DC/DC)
4.CHECK ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the engine wire from the AMD terminal (inverter with converter assembly side and No. 1 engine room relay block and junction block assembly side).


c.
A455450E01
1.167,2.438 1.573,2.719 0.406,0.281 2.958,1.365 3.313,1.604 0.354,0.24 2.979,1.385 3.292,1.583 0.313,0.198 10 true 1E 1.208,2.479 1.5,2.667 0.292,0.188 10 true C64

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C64-1 (AMD) - 1E-1 Always Below 1 Ω



d.

Install the engine wire.


Result:
Proceed to
OK
NG



OK

5.CHECK COOLING SYSTEM

NG

REPLACE ENGINE WIRE

5.CHECK COOLING SYSTEM

NEXT

6.CHECK DC/DC CONVERTER FUNCTION
6.CHECK DC/DC CONVERTER FUNCTION
HINT:

The current at the AMD terminal cannot be measured directly because of space limitations. Measure the current flowing at the auxiliary battery instead.


a.

Connect the AC/DC 400 A probe of the tester to the positive (+) auxiliary battery cable.


b.

Install the service plug grip.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.
A111747C08
0.688,1.031 1.146,0.646 1.146,0.646 1.281,0.646 true 1.177,1.26 0.896,1.656 0.896,1.656 0.75,1.656 false 1.302,0.563 1.49,0.719 0.188,0.156 10 false *a 0.552,1.563 0.75,1.708 0.198,0.146 10 false *b
*a Probe Direction
*b Current Flowing to Auxiliary Battery


Turn the ignition switch to ON (READY) and leave the vehicle as it is until the electric current flowing to the auxiliary battery becomes 10 A or less.

HINT:

If the ignition switch turns off immediately after it is turned to ON (READY), auxiliary battery voltage may be low. Recharge the auxiliary battery and perform this procedure again.



e.
A111748C08
0.729,1.042 1.146,0.646 1.146,0.646 1.281,0.646 false 1.281,1.26 0.896,1.656 0.896,1.656 0.75,1.656 false 1.302,0.563 1.479,0.719 0.177,0.156 10 false *a 0.552,1.563 0.729,1.719 0.177,0.156 10 false *b
*a Probe Direction
*b Current Flowing from Auxiliary Battery


Measure the current flowing from the auxiliary battery with the ignition switch ON (READY), the headlight position switch and blower motor switch in the HI position, and the rear window defogger turned on.

Standard Current:
Item Condition Specified Condition
Current flowing from auxiliary battery Ignition switch ON (READY)
(The headlight position switch and blower motor switch are in the HI position, and the rear window defogger is turned on.)
0 A or less
(no current from auxiliary battery)



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Item Condition Specified Condition
Auxiliary battery voltage Ignition switch ON (READY)
(The headlight position switch and blower motor switch are in the HI position, and the rear window defogger is turned on.)
12.5 to 15 V



g.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

8.CHECK HIGH VOLTAGE INSULATION
7.CHECK FUSIBLE LINK BLOCK ASSEMBLY (DC/DC)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A455827C01
2.031,0.26 2.688,0.521 false 1.406,1.156 1.406,1.823 false 0.115,0.125 0.427,0.323 0.313,0.198 10 false *1 1.792,0.167 2.104,0.365 0.313,0.198 10 false 1E 1.344,1.865 1.656,2.063 0.313,0.198 10 false 1D
*1 Fusible link block assembly


Remove the fusible link block assembly (DC/DC).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-1 - 1D-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE WIRE HARNESS

NG

REPLACE FUSIBLE LINK BLOCK ASSEMBLY (DC/DC)

8.CHECK HIGH VOLTAGE INSULATION
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the inverter cover from the inverter with converter assembly.


c.
A455017C01
1.479,0.063 1.833,0.323 0.354,0.26 2.427,0.729 2.76,0.333 true 1.542,0.115 1.781,0.281 0.24,0.167 10 true w2 2.594,0.927 2.75,1.125 0.156,0.198 10 true 1 2.104,0.479 2.26,0.677 0.156,0.198 10 true 2 1.729,0.396 1.885,0.594 0.156,0.198 10 true 3 1.354,0.427 1.51,0.625 0.156,0.198 10 true 4 1.031,0.49 1.188,0.688 0.156,0.198 10 true 5 0.656,1.302 0.813,1.5 0.156,0.198 10 true 6 2.792,0.177 3.104,0.375 0.313,0.198 10 true *1
*1 Shield Ground


Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
w2-1 (W) - Body ground and shield ground Ignition switch off 1 MΩ or higher
w2-2 (U) - Body ground and shield ground Ignition switch off 1 MΩ or higher
w2-3 (V) - Body ground and shield ground Ignition switch off 1 MΩ or higher
w2-4 (W) - Body ground and shield ground Ignition switch off 1 MΩ or higher
w2-5 (U) - Body ground and shield ground Ignition switch off 1 MΩ or higher
w2-6 (V) - Body ground and shield ground Ignition switch off 1 MΩ or higher


HINT:

Perform this inspection while the motor cable is connected.



d.

Install the inverter cover to the inverter with converter assembly.


Result:
Proceed to
OK
NG



OK

9.CHECK REAR MOTOR HIGH-VOLTAGE CIRCUIT

NG

10.CHECK GENERATOR HIGH-VOLTAGE CIRCUIT
9.CHECK REAR MOTOR HIGH-VOLTAGE CIRCUIT

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Rear Motor High-voltage Circuit

HINT:

If the "Rear Motor High-voltage Circuit" inspection results are normal, perform the next step.


Result:
Proceed to
NEXT



NEXT

REPLACE INVERTER WITH CONVERTER ASSEMBLY

10.CHECK GENERATOR HIGH-VOLTAGE CIRCUIT

NEXT

11.CHECK MOTOR HIGH-VOLTAGE CIRCUIT
11.CHECK MOTOR HIGH-VOLTAGE CIRCUIT

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Motor High-voltage Circuit

HINT:

If the "Motor High-voltage Circuit" inspection results are normal, perform the next step.


Result:
Proceed to
NEXT



NEXT

REPLACE INVERTER WITH CONVERTER ASSEMBLY