Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The following procedure is for LHD vehicles.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1.INSTALL POWER SEAT TILT MOTOR ASSEMBLY
2.INSTALL POWER SEAT LIFTER MOTOR ASSEMBLY
72125V
3.INSTALL REAR UPPER SEAT TRACK COVER
|
Install in this Direction |
Engage the 4 claws to install the rear upper seat track cover as shown in the illustration.
Use the same procedure for both sides.
72266
4.INSTALL SEAT TRACK UPPER RAIL COVER
|
Install in this Direction |
Engage the 4 claws to install the seat track upper rail cover as shown in the illustration.
Use the same procedure for both sides.
71874U
5.INSTALL FRONT LH SEAT LOWER CUSHION SHIELD
|
Install in this Direction |
Engage the claw and guide to install the front LH seat lower cushion shield as shown in the illustration.
7181B
6.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER
|
Install in this Direction |
Engage the guide as shown in the illustration.
Engage the 2 claws to install the front seat cushion wire harness holder.
Install the 2 screws.
71052A
7.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY
Engage the 6 hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.
82192
8.INSTALL FRONT SEAT WIRE
Connect each connector and engage each clamp to install the front seat wire.
71874
9.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH
for LH Side:
| *a | Hook |
| *b | Guide |
Engage the 2 claws and 2 guides to install the front seat lower cushion shield LH.
Engage the hook.
for RH Side:
| *a | Hook |
| *b | Guide |
Engage the claw and guide to install the front seat lower cushion shield LH.
Engage the hook.
71876
10.INSTALL RECLINING ADJUSTER INSIDE COVER LH
for LH Side:
Engage the 4 claws to install the reclining adjuster inside cover LH.
for RH Side:
Engage the 4 claws to install the reclining adjuster inside cover LH.
85860B
11.INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System)
Engage the hook.
Install the seat cushion climate control blower assembly with the 2 bolts.
Connect the connector and engage the wire harness clamp.
87510L
12.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
71072S
13.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Engage the 14 claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.
14.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Engage the 10 hooks to install the separate type front seat cushion cover with pad to the separate type front seat cushion spring assembly.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
for Front Passenger Side:
|
Install in this Direction |
Engage the claw to install the connector holder as shown in the illustration.
71759D
15.INSTALL FRONT NO. 2 SEATBACK HOOK
Install the 2 front No. 2 seatback hooks to the front seatback frame sub-assembly.
71588
16.INSTALL FRONT NO. 2 SEATBACK EDGE PROTECTOR
w/o Lumbar Support:
Install the 2 front No. 2 seatback edge protectors to the front seatback spring sub-assembly.
w/ Lumbar Support:
Install the 2 front No. 2 seatback edge protectors to the lumbar support adjuster assembly.
71054S
17.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY (w/o Lumbar Support)
w/ Seatback Felt:
Install the seatback felt to the front seatback spring sub-assembly.
|
Install in this Direction |
Install the front seatback spring sub-assembly to the front seatback frame sub-assembly as shown in the illustration.
Engage the 2 claws to install the 2 front No. 2 seatback edge protectors to the front seatback frame sub-assembly.
8219B
18.INSTALL FRONT SEAT NO. 2 WIRE (for Driver Side)
Engage the 2 clamps to install the front seat No. 2 wire.
8219A
19.INSTALL FRONT SEAT NO. 2 WIRE (for Front Passenger Side)
Connect the connector (D) and engage the 2 clamps (C) to install the front seat No. 2 wire.
| *A | for RHD | *B | for LHD |
w/ Climate Control Seat System:
Connect the connector (B) and engage the clamp (A).
72760D
20.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (w/ Lumbar Support)
85867A
21.INSTALL SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System (w/ Lumbar Support))
| *a | Wire Harness Clamp |
| *b | Hook |
Engage the 2 claws and 2 hooks and install the seatback climate control blower.
Connect the connector and engage the wire harness clamp.
73920A
22.INSTALL FRONT SEAT AIRBAG ASSEMBLY
87510N
23.INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
71074S
24.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Engage the 9 claws to install the separate type front seatback cover to the separate type front seatback pad.
25.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Install the separate type front seatback cover with pad.
71930A
26.INSTALL FRONT SEAT HEADREST SUPPORT ASSEMBLY
Engage the 4 claws to install the 2 front seat headrest support assemblies.
Close the 2 fasteners.
w/ Seat Heater System:
Engage the clamp.
Engage the 3 hooks.
27.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Engage the 4 guides.
Install the separate type front seatback assembly to the separate type front seat cushion assembly with the 4 bolts.
w/ Seat Heater System:
Connect the connector.
Engage the clamp.
Engage the clamp.
Connect the connector.
Engage the claw and 4 clamps to install the front seat airbag assembly wire harness.
Engage the claw first.
Engage the 2 hooks.
Pass the separate type front seatback cover through the grooves of each reclining adjuster inside cover LH.
84922C
28.INSTALL FRONT POWER SEAT SWITCH
72714
29.INSTALL SEAT ADJUSTER SHIELD CLAMP BRACKET
Install the seat adjuster shield clamp bracket to the front seat cushion shield with the 2 screws.
84921A
30.INSTALL RECLINING POWER SEAT SWITCH KNOB
Engage the 4 claws to install the reclining power seat switch knob.
84921B
31.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Engage the 4 claws to install the slide and vertical power seat switch knob.
71862
32.INSTALL FRONT SEAT INNER CUSHION SHIELD
|
Install in this Direction |
Engage the 2 claws and 2 guides as shown in the illustration.
Engage the 2 claws to install the front seat inner cushion shield.
71812D
33.INSTALL FRONT SEAT CUSHION SHIELD
Connect the front power seat switch connector.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the 3 claws and 2 guides (B) as shown in the illustration.
Engage the 2 claws to install the front seat cushion shield.
71868N
34.INSTALL FRONT SEAT FRONT CUSHION SHIELD
Engage the 3 guides.
|
Install in this Direction |
Engage the 2 claws as shown in the illustration.
|
Install in this Direction |
Engage the guide as shown in the illustration.
Install the front seat front cushion shield with the clip.
71074S
35.CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the rubber band of the separate type front seatback cover.
73240
36.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
73230
37.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
87501B
38.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
89710
39.INSTALL POSITION CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)