Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (ENGINE CONTROL) › SFI SYSTEM › from 2021.10
RM37A0E _51 Engine / Hybrid System _086905 A25A-FXS, A25B-FXS ENGINE CONTROL _0419404 SFI SYSTEM C

A25A-FXS, A25B-FXS ENGINE CONTROL  SFI SYSTEM  P15AD87  Active Grille Air Shutter "A" Missing Message  


DESCRIPTION

The ECM and swing grille actuator assembly each detect reception malfunctions. Swing grille actuator assembly reception malfunctions detected by the swing grille actuator assembly are sent to the ECM via LIN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P15AD87 Active Grille Air Shutter "A" Missing Message ECM or swing grille actuator assembly communication stops for 15.5 seconds or more with the ignition switch ON (2 trip detection logic). Radiator shutter assembly Does not come on DTC stored SAE Code: P15AD

MONITOR DESCRIPTION

When a communication malfunction occurs in either the ECM or swing grille actuator assembly, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Swing grille actuator assembly
ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 30 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P15AD87.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A473540E17
0.708,3.135 1.938,3.375 1.229,0.24 10 false Auxiliary Battery 0.552,2.115 1.781,2.354 1.229,0.24 10 false MAIN 0.729,0.667 1.354,1.115 0.625,0.448 10 false EFI-MAIN NO. 1 1.573,1.115 2.615,1.552 1.042,0.438 10 false EFI-MAIN NO. 1 1.615,0.385 2.104,0.573 0.49,0.188 10 false 3 2.406,0.385 2.896,0.573 0.49,0.188 10 false 5 2.406,0.677 2.896,0.865 0.49,0.188 10 false 2 1.625,0.667 2.115,0.854 0.49,0.188 10 false 1 2.875,1.406 4.292,1.781 1.417,0.375 10 false GRILLE SHUTTER 5.417,0.573 5.906,0.76 0.49,0.188 10 false 15 5.365,0.781 5.854,0.969 0.49,0.188 10 false A27 5.729,0.677 6.219,0.865 0.49,0.188 10 false MREL 6.469,0.771 6.76,1.031 0.292,0.26 10 false IC 5.354,2.417 5.844,2.604 0.49,0.188 10 false C55 5.417,2.198 5.906,2.385 0.49,0.188 10 false 62 5.729,2.406 6.219,2.594 0.49,0.188 10 false LIN 6.208,4.083 6.698,4.271 0.49,0.188 10 false ECM 4.313,2.406 4.802,2.594 0.49,0.188 10 false LIN 4.635,2.302 5.125,2.49 0.49,0.188 10 false 2 3.125,2.042 3.615,2.229 0.49,0.188 10 false 1 3.333,2.156 3.823,2.344 0.49,0.188 10 false +B 3.323,2.729 3.813,2.917 0.49,0.188 10 false GND 3.146,2.615 3.635,2.802 0.49,0.188 10 false 3 2.979,3.177 5.021,3.667 2.042,0.49 10 false Swing Grille Actuator Assembly 3,3.01 3.49,3.198 0.49,0.188 10 false X1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

In order to ensure safety, before performing troubleshooting or removing the radiator shutter assembly, change the grille shutter control mode to maintenance mode.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM UTILITY USING GTS (SWITCH GRILLE SHUTTER CONTROL MODE)
a.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 4672

Result:
Proceed to
NEXT



NEXT

2.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - ECM)
a.

Disconnect the swing grille actuator assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-2 (LIN) - C55-62 (LIN) Always Below 1 Ω
X1-2 (LIN) or C55-62 (LIN) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SWING GRILLE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SWING GRILLE ACTUATOR ASSEMBLY)
A473559C17
0.427,1.094 0.854,1.344 0.427,0.25 1.979,1.313 2.292,1.781 true 1.448,1.313 1.198,1.792 true 0.573,1.135 1.031,1.333 0.458,0.198 10 false X1 2.188,1.823 2.646,2.021 0.458,0.198 10 false GND 0.552,0.156 1.01,0.354 0.458,0.198 10 false *a 1.083,1.844 1.542,2.042 0.458,0.198 10 false +B
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


a.

Disconnect the swing grille actuator assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X1-1 (+B) - X1-3 (GND) Ignition switch to ON 11 to 14 V



HINT:

Perform "Switch Grille Shutter Control Mode and Grille Shutter Initialization" after replacing the radiator shutter assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

REPLACE RADIATOR SHUTTER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the swing grille actuator assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - EFI-MAIN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - EFI-MAIN NO. 1 RELAY)
a.

Disconnect the swing grille actuator assembly connector.


b.

Remove the EFI-MAIN NO. 1, VVT, EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays from the No. 1 engine room relay block and No. 1 junction block assembly.

HINT:

Remove the VVT, EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-1 (+B) - 5 (EFI-MAIN NO. 1 Relay) Always Below 1 Ω
X1-1 (+B) or 5 (EFI-MAIN NO. 1 Relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

7.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
7.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
a.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 4672

b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Grille Shutter Control Mode
50003 372 1304
Standard:
GTS Display Specified Condition
Grille Shutter Control Mode Normal



Result:
Proceed to
NEXT



NEXT

END