Water Inlet Housing Assembly
Engine Mechanical
COMPONENTS



REMOVAL
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seatbelt pretensioner activation.
HINT:
Obtain the audio system PIN from the vehicle owner, if applicable. Otherwise the audio system will be inoperable when the battery cable is reconnected.
2. DRAIN ENGINE COOLANT
(a) Allow the engine to cool.
-
(b) Remove the radiator cap.
-
(c) Loosen the 2 cylinder block drain cock plugs and radiator drain plug, and drain the coolant.
HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

-
3. DISCONNECT NO. 2 VENTILATION HOSE (
Click Here
)
4. REMOVE AIR CLEANER ASSEMBLY (
Click Here
)
5. REMOVE RADIATOR FAN AND SHROUD (
Click Here
)
6. REMOVE WATER INLET HOUSING ASSEMBLY
(a) Disconnect the 2 oil cooler hoses.
-
(b) Disconnect the 2 radiator hoses.
-
(c) Disconnect the 5 water by-pass hoses.
-
(d) Remove the 5 bolts and water inlet housing assembly.
NOTICE:
Take care when removing the housing assembly as some or all of the following components may also detach.
-
(e) Remove the 2 spacers.
-
(f) Remove the extension housing sleeve and O-rings from the water outlet pipe.
-
(g) Remove the water inlet housing sub-assembly and O-rings from the water pump.
-
INSTALLATION
1. INSTALL WATER INLET HOUSING ASSEMBLY
(a) Apply soapy water to the O-rings.
-
(b) Install the extension housing sleeve and O-rings to the water outlet pipe.
-
(c) Install the water inlet housing sub-assembly and O-rings to the water pump.
-
(d) Fit the 2 bolts into the housing assembly and fit the 2 spacers.
-
(e) Install the housing assembly and start the 2 bolts.
-
(f) Install the remaining 3 bolts.
-
(g) Tighten the 5 bolts.
Torque:
9.0 N*m
(92 kgf*cm,
7.0 ft.*lbf)
-
(h) Connect the 5 water by-pass hoses.
-
(i) Connect the 2 radiator hoses.
-
(j) Connect the 2 oil cooler hoses.
-
2. INSTALL RADIATOR FAN AND SHROUD (
Click Here
)
3. INSTALL AIR CLEANER ASSEMBLY (
Click Here
)
4. CONNECT NO. 2 VENTILATION HOSE (
Click Here
)
5. ADD ENGINE COOLANT
(a) Tighten all the drain plugs and fill the radiator with Toyota Super Long Life Coolant (SLLC).
Torque:
24.5 N*m
(250 kgf*cm,
18 ft.*lbf)
for cylinder block drain cock plug
Standard capacity:
9.8 Litres (10.4 US qts, 8.6 Imp. qts)
HINT:
Toyota vehicles are filled with Toyota SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use Toyota SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic and technology consists of a combination of low phosphates and organic acids).
NOTICE:
Never use water as a substitute for engine coolant.
-
(b) Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
-
(c) Install the radiator cap.
-
(d) Bleed air from the cooling system.
(1) Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
(2) Maintain the engine speed at 2,000 to 2,500 rpm.
(3) Press the inlet and outlet radiator hoses several times by hand to bleed air.
CAUTION:
When pressing the radiator hoses:
• Wear protective gloves.
• Be careful as the radiator hoses are hot.
• Keep your hands away from the radiator fan.
-
(e) Stop the engine and wait until the coolant cools down to ambient temperature.
CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurised, hot engine coolant and steam may be released and cause serious burns.
-
(f) Check the coolant level in the radiator reservoir.
If the coolant level is low, add SLLC to the reservoir F line.
-
6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
7. CHECK COOLING SYSTEM FOR LEAKS
CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurised, hot engine coolant and steam may be released and cause serious burns.
(a) Fill the radiator with coolant and attach a radiator cap tester.
-
(b) Warm up the engine.
-
(c) Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the cylinder block and head.
-
8. PERFORM INITIALISATION
(a) Enter the audio system PIN, if applicable. Refer to Section 1-8 "Audio System" in the TRD Hilux Driver's Manual for programming information.
-
(b) Calibrate the multi-information display compass. Refer to Section 1-10 "Other Equipment" in the TRD Hilux Driver's Manual for calibrating information.
-