2008-2009 Hilux TRD · Service Manual Suspension

Rear Leaf Spring

Suspension

COMPONENTS
REMOVAL
HINT:
• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.
1. REMOVE REAR WHEEL
2. REMOVE NO. 3 PARKING BRAKE CABLE
(a) Remove the bolt and disconnect the cable from the spring.
-
3. REMOVE REAR SHOCK ABSORBER ASSEMBLY ( Click Here )
4. REMOVE REAR LEAF SPRING U BOLT
(a) Remove the 4 nuts, 4 washers, 2 U bolts, rear spring bumper and U bolt seat.
-
5. REMOVE REAR LEAF SPRING PIN BOLT
(a) Remove the nut, washer and pin bolt.
-
6. REMOVE LEAF SPRING SHACKLE INNER PLATE
(a) Remove the 2 nuts, 2 washers and inner plate.
-
7. REMOVE NO. 2 REAR LEAF SPRING SHACKLE SUB-ASSEMBLY
(a) Using a screwdriver, remove the spring shackle.
HINT:
Tape the screwdriver tip before use.
-
8. REMOVE REAR LH LEAF SPRING ASSEMBLY
(a) Remove the spring from the vehicle body.
-
DISASSEMBLY
1. REMOVE REAR LEAF SPRING SHACKLE LOWER BUSH
(a) Using a screwdriver, remove the 2 bushes from the spring shackle side or spring side.
HINT:
Tape the screwdriver tip before use.
-
2. REMOVE REAR LEAF SPRING SHACKLE UPPER BUSH
(a) Using a screwdriver, remove the 2 bushes from the spring shackle side or spring side.
HINT:
Tape the screwdriver tip before use.
-
REASSEMBLY
1. INSTALL REAR LEAF SPRING SHACKLE UPPER BUSH
(a) Install the 2 bushes to the spring side.
-
2. INSTALL REAR LEAF SPRING SHACKLE LOWER BUSH
(a) Install the 2 bushes to the spring side.
-
INSTALLATION
1. INSTALL REAR LH LEAF SPRING ASSEMBLY
(a) Install the spring to the vehicle body.
-
2. INSTALL NO. 2 REAR LEAF SPRING SHACKLE SUB-ASSEMBLY
(a) Install the spring shackle to the spring and vehicle frame.
-
3. TEMPORARILY INSTALL LEAF SPRING SHACKLE INNER PLATE
(a) Temporarily install the inner plate to the shackle No. 2 with the 2 washers and 2 nuts.
HINT:
After stabilising the suspension, torque the nut.
-
4. TEMPORARILY INSTALL REAR LEAF SPRING PIN BOLT
(a) Temporarily install the pin bolt with the washer and nut.
HINT:
• The pin bolt can be installed from either side of the spring.
• After stabilising the suspension, torque the nut.
-
5. TEMPORARILY INSTALL REAR LEAF SPRING U BOLT
(a) Temporarily install the U bolt seat and rear spring bumper with the 2 U bolts, 4 washers and 4 nuts.
HINT:
When tightening the U bolts, tighten the nuts in diagonal pairs.
-
6. INSTALL REAR SHOCK ABSORBER ASSEMBLY ( Click Here )
7. INSTALL NO. 3 PARKING BRAKE CABLE
(a) Connect the cable to the spring with the bolt.
-
8. STABILISE SUSPENSION
(a) Lower the vehicle.
-
(b) Press down on the vehicle several times to stabilise the suspension.
-
9. TIGHTEN LEAF SPRING SHACKLE INNER PLATE NUT
(a) Tighten the inner plate with the 2 nuts.
Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)
-
10. TIGHTEN LEAF SPRING PIN NUT
(a) Tighten the pin nut.
Torque:
120 N*m (1,224 kgf*cm, 89 ft.*lbf)
-
11. TIGHTEN LEAF SPRING U-BOLT SEAT NUT
(a) Tighten the set nut.
Torque:
120 N*m (1,224 kgf*cm, 89 ft.*lbf)
-
12. INSTALL REAR WHEEL
(a) Install the wheel.
Torque:
105 N*m (1,070 kgf*cm, 77 ft.*lbf)
-