Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

ECD SYSTEM (w/ EGR Cooler) > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes a current to flow to the coil, closing the contacts of the MAIN relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM


A159339E01


INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs initialization (Click here).

1.CHECK ECM (+B VOLTAGE)


    A080463E28
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (E5-1) - E1 (E7-7)
    11 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
NG


2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)


    A065745E92
  1. Disconnect the E7 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E1 (E7-7) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK ECM (IGSW VOLTAGE)


    A080463E29
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    IGSW (E5-9) - E1 (E7-7)
    11 to 14 V



OK
Go to step 6
NG


4.INSPECT FUSE (IGN FUSE)


    A155929E01
  1. Remove the IGN fuse from the instrument panel J/B.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


5.INSPECT IGNITION SWITCH ASSEMBLY


    A056879E52
  1. Disconnect the I6 ignition switch connector.

  1. Measure the resistance of the ignition switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (AM2) - 6 (IG2)
    LOCK
    10 kΩ or higher
    5 (AM2) - 6 (IG2)
    ON
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK


6.CHECK ECM (MREL VOLTAGE)


    A080463E30
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    MREL (E5-8) - E1 (E7-7)
    11 to 14 V



NG
REPLACE INTEGRATION NO.1 RELAY (Click here)
OK


7.INSPECT FUSE (EFI FUSE)


    A159237E01
  1. Remove the EFI fuse from the engine room junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


8.INSPECT INTEGRATION NO.1 RELAY (MAIN RELAY)


    G039047E14
  1. Remove the integration relay from the engine room junction block .

  1. Measure the voltage of the integration relay

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1J-4 - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPLACE INTEGRATION NO.1 RELAY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY (MAIN RELAY) - ECM)


    G034918E07
  1. Disconnect the 1J integration relay connector from the engine room J/B .

  1. Disconnect the E5 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (check for open):
    Tester Connection
    Specified Condition
    1J-4 - +B (E5-1)
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Specified Condition
    1J-4 or +B (E5-1) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY (MAIN RELAY) - ECM)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (+B TERMINAL OF ECM - BATTERY POSITIVE TERMINAL)