Home › TRANSMISSION ยท A343F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch OFF.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the intelligent tester ON.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. Follow the instructions on the tester and read the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch
    Stop light switch status/
    ON or OFF
    Brake pedal is
    1. ON: Depressed
    2. OFF: Released
    -
    Neutral Position SW Signal
    Park/neutral position switch status/
    ON or OFF
    Shift lever is:
    1. ON: On P or N
    2. OFF: Not on P or N
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to Park/Neutral Position Switch Circuit (Click here)

    Shift SW Status (R Range)
    Park/neutral position switch status/
    ON or OFF
    Shift lever is:
    1. ON: On R
    2. OFF: Not on R
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to Park/Neutral Position Switch Circuit (Click here)

    Shift SW Status (D or 3 Range)
    Park/neutral position switch status/
    ON or OFF
    Shift lever is:
    1. ON: On D or 3
    2. OFF: Not on D or 3
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to Park/Neutral Position Switch Circuit (Click here)

    Shift SW Status (2 Range)
    Park/neutral position switch status/
    ON or OFF
    Shift lever is:
    1. ON: On 2
    2. OFF: Not on 2
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to Park/Neutral Position Switch Circuit (Click here)

    Shift SW Status (L Range)
    Park/neutral position switch status/
    ON or OFF
    Shift lever is:
    1. ON: On L
    2. OFF: Not on L
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to Park/Neutral Position Switch Circuit (Click here)

    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd or 4th
    Shift lever position is:
    1. On L: 1st
    2. On 2: 1st or 2nd
    3. On 3: 1st, 2nd or 3rd
    4. On D: 1st, 2nd, 3rd or 4th
    -
    Lock Up Solenoid Status
    Lock-up solenoid status/
    ON or OFF
    Lock-up solenoid is:
    1. ON: Operating
    2. OFF: Not operating
    -
    SLT Solenoid Status
    Shift solenoid SLT status/
    ON or OFF
    1. ON: Accelerator pedal is released
    2. OFF: Accelerator pedal is depressed
    -
    A/T Oil Temperature 3
    ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall speed test:
      Approximately 80°C (176°F)
    2. Equal to ambient temperature while engine is cold
    If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or short circuited
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph)
    (output shaft speed is equal to vehicle speed)
    -
    SPD (NC0)
    Input turbine speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Lock-up ON (warmed up engine, other than 4th):
      Input turbine speed (NC0) is equal to the engine speed
    2. Lock-up ON (warmed up engine, 4th):
      Input turbine speed (NC0) is 0 rpm
    3. Lock-up OFF (idling with shift lever on N):
      Input turbine speed (NC0) is nearly equal to engine speed
    Data is displayed in increments of 50 rpm


PERFORM ACTIVE TEST

HINT:
Performing the intelligent tester's Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.
The Data List can be displayed during the Active Test.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the intelligent tester ON.

  4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  5. Perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operate shift solenoid valve and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (30 mph) or less
    Control the Lock Up
    Control shift solenoid SL to set automatic transmission to lock-up condition
    ON or OFF
    Possible to check shift solenoid valve SL operation
    [Vehicle Condition]
    Vehicle speed: 60 km/h (36 mph) or more
    Control the Line Pressure Up*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling

    HINT:
    *: "Control the Line Pressure Up" in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.