ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / ECT / Data List.
Follow the instructions on the tester and read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Actual vehicle speed | Speed indicated on speedometer |
| Engine Speed | Engine speed/ Min.: 0 rpm Max.: 16383.75 rpm | Engine idling: 700 to 800 rpm | - |
| Calculate Load | Calculated load by ECM/ Min.: 0% Max.: 100% | Running without load (2500 rpm): 13.1 to 18.9% | - |
| Coolant Temp | Engine coolant temperature/ Min.: -40°C (-40°F) Max.: 140°C (284°F) | After warming up engine: 80 to 90°C (176 to 194°F) |
|
| Engine Run Time | Engine run time/ Min.: 0 seconds, Max.: 65535 seconds | Time after engine start | - |
| Battery Voltage | Battery voltage/ Min.: 0 V Max.: 65.535 V | Engine idling: 11 to 14 V | - |
| Starter Signal | Starter signal/ ON or OFF |
| - |
| Neutral Position SW Signal | PNP switch status/ ON or OFF | Shift lever is: On P or N: ON Not on P or N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Stop Light Switch | Stop light switch status/ ON or OFF |
| - |
| Check Mode | Check mode/ ON or OFF | ON: Check mode ON | - |
| SPD Test Result | Check mode result for vehicle/ Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor/ Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor/ Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Heater Monitor | Heated oxygen sensor (air fuel ratio sensor) heater monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | Heated oxygen sensor (air fuel ratio sensor) heater monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Monitor | Heated oxygen sensor (air fuel ratio sensor) monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Monitor | Heated oxygen sensor (air fuel ratio sensor) monitor/ Compl or Incmpl | - | - |
| A/C Monitor | A/C monitor/ Not Avl or Avail | - | - |
| A/C Monitor | A/C monitor/ Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd air monitor/ Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd air monitor/ Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor/ Not Avl or Avail | - | - |
| EVAP Monitor | EVAP monitor/ Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor/ Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor/ Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor/ Compl or Incmpl | - | - |
| # Codes (Include History) | # of Codes/ Min.: 0 Max.: 255 | - | Number of detected DTCs |
| MIL | MIL status/ ON or OFF | ON: MIL ON | - |
| MIL ON Run Distance | MIL ON run distance/ Min.: 0 km (0 mile) Max.: 65535 km (40723 mile) | Distance after DTC stored | - |
| Running Time from MIL ON | Running time from MIL on/ Min.: 0 minutes, Max.: 65535 minutes | Equivalent to running time after MIL turns on | - |
| Time after DTC Cleared | Time after DTC cleared/ Min.: 0 minutes, Max.: 65535 minutes | Equivalent to time after DTCs cleared | - |
| Distance from DTC Cleared | Distance after DTC cleared/ Min.: 0 km (0 mile) Max.: 65535 km (40723 mile) | Equivalent to distance driven after DTCs cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared/ Min.: 0, Max.: 255 | - | Number of warm-up cycles after DTCs cleared |
| Number of Emission DTC | Number of emission DTCs | - | - |
| Model Code | Model Code/ | - | - |
| Engine Type | Engine Type/ | - | - |
| Cylinder Number | Cylinder number/ | - | - |
| Destination | Destination/ | - | - |
| Model Year | Model year/ | - | - |
| Engine Speed from EFI | Engine speed/ Min.: 0 rpm Max.: 16383.75 rpm | - | Engine speed received from the ECM. |
| Intake-Air Temp from EFI | Intake air temperature/ Min.: -40°C (-40°F) Max.: 215°C (419°F) | - | Intake air temperature received from the ECM. |
| Coolant Temp from EFI | Engine coolant temperature/ Min.: -40°C (-40°F) Max.: 215°C (419°F) | - | Coolant temperature received from the ECM. |
| Accel Position from EFI | Absolute accelerator pedal position/ Min.: 0% Max.: 100% | - | - |
| Injection Volume from EFI | Injection volume/ Min.: -10 mm3 Max.: 1,279.98 mm3 | - | - |
| SPD (NC0) | Input turbine speed/ Min.: 0 rpm Max.: 12750 rpm |
| - |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) | - |
| Shift SW Status (R Range) | PNP switch status/ ON or OFF | Shift lever is: On R: ON Not on R: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (2 Range) | PNP switch status/ ON or OFF | Shift lever is: On 2: ON Not on 2: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (L Range) | PNP switch status/ ON or OFF | Shift lever is: On L: ON Not on L: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (D Range) | PNP switch status/ ON or OFF | Shift lever is: On D: ON Not on D: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (3 Range) | PNP switch status/ ON or OFF | Shift lever is: On 3: ON Not on 3: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| A/T Oil Temperature 3 | ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor circuit is opened or short circuited |
| Lock Up | Lock-up/ ON or OFF |
| - |
| Lock Up Solenoid Status | Lock-up solenoid status/ ON or OFF |
| - |
| Shift Status | ECM gear shift command/ 1st, 2nd, 3rd or 4th (O/D) | Shift lever position is:
| - |
| SLT Solenoid Status | Shift solenoid SLT status/ ON or OFF |
| - |
| PERFORM ACTIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / ECT / Active Test.
Perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON or OFF | - |
| Activate the Solenoid (SLT)* | Operate shift solenoid valve SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
| Activate the Solenoid (S1) | Operate shift solenoid valve S1 | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (S2) | Operate shift solenoid valve S2 | ON or OFF | [Vehicle Condition]
|
| Activate the Lock Up | Control shift solenoid valve SLT to set automatic transmission to lock-up | ON or OFF | Possible to check shift solenoid valve SLT operation. [Vehicle Condition]
|
| Activate the Solenoid (SL) | Operate shift solenoid valve SL | ON or OFF | [Vehicle Condition]
|
| Control the Shift Position | Operate shift solenoid valves and set each shift position |
| Possible to check operation of the shift solenoid valves. [Vehicle Condition] 50 km/h (31 mph) or less |