REAR DIFFERENTIAL CARRIER ASSEMBLY (for DANA Made) > REASSEMBLY |
| 1. INSTALL DIFFERENTIAL RING GEAR |
![]() |
Clean the contact surfaces of the differential case and ring gear.
Heat the ring gear in boiling water that is approximately 100°C (212°F).
Carefully remove the ring gear from the boiling water.
After the moisture on the ring gear has completely evaporated, quickly install the ring gear to the differential case.
![]() |
Align the matchmarks on the ring gear with those of the differential case.
Temporarily install the 10 bolts.
After the ring gear cools down, uniformly tighten the 10 bolts in diametrically opposite pairs in several passes.
| 2. INSTALL REAR DIFFERENTIAL CASE BEARING |
![]() |
Using SST and a press, press the bearing onto the differential case.
| 3. INSPECT DIFFERENTIAL RING GEAR RUNOUT |
![]() |
Install the differential case on the carrier, and install the 2 side shims so that there is no play in the bearing.
Install the 2 bearing caps with the 4 bolts.
Using a dial indicator, measure the runout of the ring gear.
Remove the 2 bearing caps, 2 side shims and differential case.
| 4. INSTALL REAR DIFFERENTIAL DUST DEFLECTOR |
![]() |
Using SST, a plate and a press, press in the dust deflector.
| 5. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST and a press, press the roller bearing (outer) to the carrier.
| 6. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Using SST and a press, press the roller bearing (outer) into the carrier.
| 7. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Install the plate washer on the drive pinion.
Using SST and a press, press the roller bearing (inner) onto the drive pinion.
| 8. ADJUST DIFFERENTIAL DRIVE PINION PRELOAD |
![]() |
Install a new bearing spacer to the drive pinion.
![]() |
Install the rear drive pinion front tapered roller bearing.
Install the rear differential drive pinion oil slinger.
Apply MP grease to a new oil seal.
![]() |
Using SST, install the companion flange on the drive pinion.
![]() |
Using SST to hold the companion flange in place, torque the nut.
![]() |
Using a torque wrench, measure the preload.
| Bearing | Preload |
| New bearing | 1.05 to 1.64 N*m (10.7 to 16.7 kgf*cm, 9.3 to 14.5 in.*lbf) |
| Reused bearing | 0.56 to 0.85 N*m (5.7 to 8.7 kgf*cm, 4.9 to 7.5 in.*lbf) |
| 9. INSTALL DIFFERENTIAL CASE ASSEMBLY |
![]() |
Place the 2 bearing outer races on their respective bearings and 2 side shims.
![]() |
Align matchmarks on the bearing cap and differential carrier, and install the 2 bearing caps.
Tighten both bearing caps with the 4 bolts.
| 10. INSPECT BACKLASH DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH |
![]() |
Set the dial indicator perpendicular to the end of the ring gear face.
While holding the rear drive pinion companion flange, rotate the ring gear and measure the backlash.
| 11. ADJUST DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH |
![]() |
Select a side shim so that the ring gear backlash is within the specification. Then, install it to the ring gear back side.
| Thickness | Thickness | Thickness |
| 2.51 mm (0.099 in.) | 3.12 mm (0.123 in.) | 3.73 mm (0.147 in.) |
| 2.54 mm (0.100 in.) | 3.15 mm (0.124 in.) | 3.76 mm (0.148 in.) |
| 2.57 mm (0.101 in.) | 3.18 mm (0.125 in.) | 3.78 mm (0.149 in.) |
| 2.59 mm (0.102 in.) | 3.20 mm (0.126 in.) | 3.81 mm (0.150 in.) |
| 2.62 mm (0.103 in.) | 3.23 mm (0.127 in.) | 3.84 mm (0.151 in.) |
| 2.64 mm (0.104 in.) | 3.25 mm (0.128 in.) | 3.86 mm (0.152 in.) |
| 2.67 mm (0.105 in.) | 3.28 mm (0.129 in.) | 3.89 mm (0.153 in.) |
| 2.69 mm (0.106 in.) | 3.30 mm (0.130 in.) | 3.91 mm (0.154 in.) |
| 2.72 mm (0.107 in.) | 3.33 mm (0.131 in.) | 3.94 mm (0.155 in.) |
| 2.74 mm (0.108 in.) | 3.35 mm (0.132 in.) | 3.96 mm (0.156 in.) |
| 2.77 mm (0.109 in.) | 3.38 mm (0.133 in.) | 3.99 mm (0.157 in.) |
| 2.79 mm (0.110 in.) | 3.40 mm (0.134 in.) | 4.01 mm (0.158 in.) |
| 2.82 mm (0.111 in.) | 3.43 mm (0.135 in.) | 4.04 mm (0.159 in.) |
| 2.84 mm (0.112 in.) | 3.45 mm (0.136 in.) | 4.06 mm (0.160 in.) |
| 2.87 mm (0.113 in.) | 3.48 mm (0.137 in.) | 4.09 mm (0.161 in.) |
| 2.90 mm (0.114 in.) | 3.51 mm (0.138 in.) | 4.11 mm (0.162 in.) |
| 2.92 mm (0.115 in.) | 3.53 mm (0.139 in.) | 4.14 mm (0.163 in.) |
| 2.95 mm (0.116 in.) | 3.56 mm (0.140 in.) | 4.17 mm (0.164 in.) |
| 2.97 mm (0.117 in.) | 3.58 mm (0.141 in.) | 4.19 mm (0.165 in.) |
| 3.00 mm (0.118 in.) | 3.61 mm (0.142 in.) | 4.22 mm (0.166 in.) |
| 3.02 mm (0.119 in.) | 3.63 mm (0.143 in.) | 4.24 mm (0.167 in.) |
| 3.05 mm (0.120 in.) | 3.66 mm (0.144 in.) | 4.27 mm (0.168 in.) |
| 3.07 mm (0.121 in.) | 3.68 mm (0.145 in.) | 4.29 mm (0.169 in.) |
| 3.10 mm (0.122 in.) | 3.71 mm (0.146 in.) | - |
Make the differential case bearing and side shim snug by tapping on the ring gear with a plastic-faced hammer.
![]() |
Set the dial indicator perpendicular to the end of the ring gear face.
While holding the rear drive pinion companion flange, rotate the ring gear and measure the backlash.
![]() |
If the backlash is not within the specification, select a side shim so that the ring gear backlash is within the specification. Then, install it to the ring gear back side.
![]() |
Select a thicker side shim so that the clearance between the case bearing outer race end on the ring gear teeth side and the carrier becomes 0 or around 0.
Make the differential case bearing and side shim snug by tapping on the ring gear with a plastic-faced hammer.
![]() |
Select the dial indicator perpendicular to the end of the ring gear face.
While holding the rear drive pinion companion flange rear, rotate the ring gear and measure the backlash.
| 12. INSPECT TOTAL PRELOAD |
![]() |
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
| 13. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION |
![]() |
Coat 3 or 4 teeth at 3 different positions on the ring gear with red lead primer.
Hold the companion flange firmly in place and rotate the ring gear in both directions.
Inspect the tooth contact pattern.

![]() |
| Thickness mm (in.) | Thickness mm (in.) |
| 0.69 mm (0.0272 in.) | 1.19 mm (0.0469 in.) |
| 0.71 mm (0.0280 in.) | 1.22 mm (0.0480 in.) |
| 0.74 mm (0.0291 in.) | 1.24 mm (0.0488 in.) |
| 0.76 mm (0.0300 in.) | 1.27 mm (0.0500 in.) |
| 0.79 mm (0.0311 in.) | 1.30 mm (0.0512 in.) |
| 0.81 mm (0.0319 in.) | 1.32 mm (0.0520 in.) |
| 0.84 mm (0.0331 in.) | 1.35 mm (0.0531 in.) |
| 0.86 mm (0.0339 in.) | 1.37 mm (0.0540 in.) |
| 0.89 mm (0.0350 in.) | 1.40 mm (0.0551 in.) |
| 0.91 mm (0.0358 in.) | 1.42 mm (0.0559 in.) |
| 0.94 mm (0.0370 in.) | 1.45 mm (0.0571 in.) |
| 0.97 mm (0.0382 in.) | 1.47 mm (0.0579 in.) |
| 0.99 mm (0.0390 in.) | 1.50 mm (0.0591 in.) |
| 1.02 mm (0.0402 in.) | 1.52 mm (0.0598 in.) |
| 1.04 mm (0.0409 in.) | 1.55 mm (0.0610 in.) |
| 1.07 mm (0.0421 in.) | 1.58 mm (0.0622 in.) |
| 1.09 mm (0.0429 in.) | 1.60 mm (0.0630 in.) |
| 1.12 mm (0.0441 in.) | 1.63 mm (0.0642 in.) |
| 1.14 mm (0.0449 in.) | 1.65 mm (0.0650 in.) |
| 1.17 mm (0.0461 in.) | - |
| 14. REMOVE REAR DRIVE PINION NUT |
![]() |
Using SST and a hammer, loosen the staked part of the nut.
![]() |
Using SST to hold the companion flange in place, remove the nut.
| 15. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
| 16. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
| 17. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST, remove the roller bearing (outer) from the carrier.
Using a brass bar and hammer, tap out the oil storage ring from the carrier.
| 18. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
![]() |
Install a new bearing spacer to the drive pinion.
| 19. INSTALL DIFFERENTIAL OIL STORAGE RING |
Using a brass bar and hammer, tap in a new oil storage ring.
| 20. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
| 21. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
| 22. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL |
Apply MP grease to the lip of a new oil seal.
Using a brass bar and hammer, tap in a new oil seal until its surface is flush with the differential carrier end.
| 23. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Using SST, install the companion flange on the drive pinion.
![]() |
Using SST to hold the flange, torque the nut.
| 24. INSPECT DRIVE PINION PRELOAD |
![]() |
Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.
| Bearing | Preload |
| New bearing | 1.20 to 2.00 N*m (12 to 20 kgf*cm, 11 to 18 in.*lbf) |
| Reused bearing | 0.70 to 1.50 N*m (7 to 15 kgf*cm, 6.0 to 13 in.*lbf) |
| 25. INSPECT TOTAL PRELOAD |
![]() |
Using a torque wrench, measure the preload.
| 26. INSPECT DIFFERENTIAL RING GEAR BACKLASH |
![]() |
Using a dial indicator, measure the backlash of the ring gear.
| 27. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the runout of the drive pinion companion flange vertically and laterally.
| Runout | Maximum |
| Vertical runout | 0.10 mm (0.0039 in.) |
| Lateral runout | 0.10 mm (0.0039 in.) |
| 28. STAKE DRIVE PINION NUT |
![]() |
Using a chisel and hammer, stake the nut.