Home › TRANSMISSION ยท G58F MANUAL TRANSMISSION › MANUAL TRANSMISSION ASSEMBLY

MANUAL TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TRANSFER ASSEMBLY
  1. Install the transfer (Click here).



2. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY


C112945E02
  1. Align the input shaft with the clutch disc and install the transmission to the engine.

  1. Install the 4 bolts.

    Torque:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf }



3. INSTALL STIFFENER PLATE


C121621E06
  1. Install the stiffener plate RH with the 4 bolts.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf } for bolt A
    37 N*m{ 377 kgf*cm , 27 ft.*lbf } for bolt B

  1. Install the stiffener plate LH with the 4 bolts.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf } for bolt A
    37 N*m{ 377 kgf*cm , 27 ft.*lbf } for bolt B



4. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR


G034226E01
  1. Install the mounting insulator with the 4 bolts.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



5. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


B085193E07
  1. Install the frame crossmember with the 4 bolts and 4 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Install the 4 set bolts to the rear No. 1 engine mounting insulator.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



6. INSTALL STARTER ASSEMBLY
  1. Install the starter (Click here).



7. CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY


G034223E01
  1. Install the release cylinder with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



8. CONNECT WIRE HARNESS
  1. Transmission side:
    Connect the back-up light switch connector.

  1. Transfer side:
    Connect the No. 1, No. 2 and No. 3 transfer indicator switch connectors, and vehicle speed sensor connector.



9. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install the front exhaust pipe (Click here).



10. INSTALL REAR PROPELLER SHAFT ASSEMBLY
  1. Install the rear propeller shaft (Click here).



11. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
  1. Install the front propeller shaft (Click here).



12. ADD MANUAL TRANSMISSION OIL


D025304E08

Oil grade:
GL-4 or GL-5

Viscosity:
SAE 75W-90

Standard capacity:
2.6 liters (2.7 US qts, 2.3 Imp. qts)

Torque:
37 N*m{ 377 kgf*cm , 27 ft.*lbf }



13. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }



14. INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }



15. INSTALL TRANSFER CASE LOWER PROTECTOR
  1. Install the transfer case lower protector with the 4 bolts.

    Torque:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }



16. INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY
  1. Install the transfer shift lever.

  1. Using pliers, install the snap ring.

    HINT:
    Apply MP grease to the tip of the transfer shift lever.



17. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY
  1. Cover the shift lever cap with a cloth.

  1. Press down on the shift lever cap and rotate it clockwise to install it.

    HINT:
    Apply MP grease to the tip of the shift lever.



18. INSTALL SHIFT LEVER BOOT ASSEMBLY


G034544E02
  1. Install the shift lever boot with the 4 screws and 2 clips.

  1. w/o Console Box:
    Install the floor carpet, front seat, front door scuff plate, etc.



19. INSTALL CONSOLE BOX ASSEMBLY


B090153E01
  1. Install the console box with the 2 clips, 4 screws <F> and 2 bolts <E>.



20. INSTALL UPPER CONSOLE PANEL ASSEMBLY


B115418E02

NOTICE:
Be careful not to damage the instrument panel lower and console box with the claws of the console panel upper.

  1. Attach the 12 claws to install the console panel.



21. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


B111105E01
  1. w/ M/T:
    Twist the knob in the direction indicated by the arrow to install it.

  1. w/ 4WD:
    Twist the transfer shift lever knob in the direction indicated by the arrow to install it.



22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


23. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



24. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).