CYLINDER HEAD > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. DRAIN ENGINE OIL |
| 3. LOOSEN FUEL TANK CAP ASSEMBLY |
| 4. DRAIN FUEL |
| 5. REMOVE FAN SHROUD |
![]() |
Remove the 3 bolts and oil reservoir.
Disconnect the No. 1 and No. 2 water by-pass hoses from the tank upper and lower.
Remove the 2 bolts and radiator reservoir.
Loosen the 4 nuts holding the fluid coupling fan.
Remove the drive belt .
Remove the 2 bolts holding the fan shroud.
Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.
Remove the fan pulley from the water pump.
| 6. REMOVE FAN PULLEY |
Remove the 4 nuts and pulley.
| 7. DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System) |
Remove the 4 bolts and disconnect the cooler compressor.
| 8. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System) |
Remove the 4 bolts and mounting bracket.
| 9. REMOVE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (for Cold Area Specification Vehicles) |
![]() |
Disconnect the connector.
Remove the 2 bolts and viscous with magnet clutch heater assembly.
| 10. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles) |
Remove the 2 bolts and bracket.
| 11. REMOVE TURBOCHARGER SUB-ASSEMBLY |
w/ EGR Cooler:
Remove the turbocharger sub-assembly (Click here).
w/o EGR Cooler:
Remove the turbocharger sub-assembly (Click here).
| 12. REMOVE EXHAUST MANIFOLD |
![]() |
w/o EGR Cooler:
Remove the 8 nuts, 8 spacers and exhaust manifold as shown in the illustration.
w/ EGR Cooler:
Remove the 8 nuts, 8 spacers, 8 collars and exhaust manifold as shown in the illustration.
| 13. REMOVE GLOW PLUG ASSEMBLY |
w/ EGR Cooler:
Remove the glow plug assembly (Click here).
w/ EGR System:
Remove the glow plug assembly (Click here).
w/o System:
Remove the glow plug assembly (Click here).
| 14. REMOVE MANIFOLD STAY (w/o EGR Cooler) |
![]() |
Remove the 2 bolts and stay.
| 15. DISCONNECT WIRE HARNESS |
| 16. REMOVE INJECTION PIPE (w/o EGR Cooler) |
![]() |
Remove the 2 nuts and No. 3 injection pipe clamp.
Remove the bolt and No. 2 injection pipe clamp.
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
![]() |
Remove the 2 bolts and disconnect the 2 injection pipe clamps.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
| 17. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY (w/o EGR Cooler) |
![]() |
Disconnect the 2 fuel hoses.
Remove the check valve, 3 bolts, leakage pipe and gasket.
| 18. REMOVE INTAKE MANIFOLD (w/o EGR Cooler) |
![]() |
Remove the 4 bolts, 2 nuts, manifold and gasket.
| 19. REMOVE INTAKE MANIFOLD (w/ EGR Cooler) |
Remove the intake manifold (Click here).
| 20. REMOVE NO. 1 TIMING BELT COVER |
Remove the bolt and water hose clamp.
Remove the wire harness clamp.
![]() |
Remove the 6 bolts and timing belt cover.
| 21. REMOVE TIMING BELT |
![]() |
Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
![]() |
Uniformly loosen the 2 bolts and remove the timing belt tensioner.
Remove the timing belt.
Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.
![]() |
| 22. REMOVE NOZZLE HOLDER SEAL |
![]() |
Using a small screwdriver, remove the holder seal by prying the portion between the holder seal and the cutout part of the cylinder head.
| 23. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
| 24. REMOVE CAMSHAFT TIMING PULLEY |
![]() |
Remove the bolt of the camshaft timing pulley by holding the camshaft with a wrench.
Remove the camshaft timing pulley.
| 25. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY |
| 26. REMOVE NO. 2 TIMING BELT COVER |
Remove the 4 bolts, nut and timing belt cover.
| 27. REMOVE CYLINDER BLOCK INSULATOR (w/ EGR Cooler) |
![]() |
Remove the cylinder block insulator form the head.
| 28. REMOVE INJECTOR ASSEMBLY |
![]() |
Remove the union bolt, 4 hollow screws, 5 gaskets and nozzle leakage pipe.
![]() |
Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.
Remove the O-ring and back-up ring from the injector.
Remove the 4 injection nozzle sheets from the cylinder head.
| 29. REMOVE CAMSHAFT |
![]() |
Face the key groove of the camshaft upward by turning the camshaft with a wrench.
![]() |
Uniformly loosen the 15 bearing cap bolts in several passes in the sequence shown in the illustration.
Remove the 5 bearing caps, oil seal and 2 camshafts.
| 30. REMOVE CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Uniformly loosen and remove the 18 cylinder head bolts in several passes in the sequence shown in the illustration.
Lift the cylinder head from the dowels on the cylinder block, and place the cylinder head on wooden blocks on a bench.
| 31. REMOVE CYLINDER HEAD GASKET |