Home › ENGINE ยท 1KD-FTV › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. DRAIN ENGINE OIL
  1. Remove the oil filter cap.

  1. Remove the oil drain plug, and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in an oil disposal container.



3. LOOSEN FUEL TANK CAP ASSEMBLY


4. DRAIN FUEL


5. REMOVE FAN SHROUD


A099548E01
  1. Remove the 3 bolts and oil reservoir.

  1. Disconnect the No. 1 and No. 2 water by-pass hoses from the tank upper and lower.

  1. Remove the 2 bolts and radiator reservoir.

  1. Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the drive belt .

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.



6. REMOVE FAN PULLEY
  1. Remove the 4 nuts and fan pulley.



7. DISCONNECT COOLER COMPRESSOR ASSEMBLY
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



8. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
  1. Remove the 4 bolts and mounting bracket.



9. REMOVE TURBOCHARGER SUB-ASSEMBLY
  1. w/ EGR cooler:
    Remove the turbocharger sub-assembly (Click here).

  1. w/o EGR cooler:
    Remove the turbocharger sub-assembly (Click here).



10. REMOVE EXHAUST MANIFOLD


    A152664
  1. Remove the 8 nuts and exhaust manifold as shown in the illustration.



11. REMOVE GLOW PLUG ASSEMBLY
  1. w/ EGR cooler:
    Remove the glow plug assembly (Click here).

  1. w/o EGR cooler:
    Remove the glow plug assembly (Click here).



12. DISCONNECT WIRE HARNESS


13. REMOVE INTAKE MANIFOLD
  1. w/ EGR cooler:
    Remove the intake manifold assembly (Click here).

  1. w/o EGR cooler:
    Remove the intake manifold assembly (Click here).



14. REMOVE NO. 1 TIMING BELT COVER


A015094E01
  1. Remove the bolt and water hose clamp.

  1. Remove the wire harness clamp.

  1. Remove the 6 bolts and timing belt cover.



15. REMOVE TIMING BELT


A070549E02
  1. Turn the crankshaft clockwise and align the timing marks as shown in the illustration.



    A070550E01
  1. Uniformly loosen the 2 bolts and remove the timing belt tensioner.

  1. Remove the timing belt.

  1. Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.

    HINT:

    1. A070551E02
    2. When turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise.
    3. When installing the timing belt, return the camshaft to the timing marks and then turn the crankshaft clockwise until it aligns with the timing marks, as shown in the illustration.



16. REMOVE NOZZLE HOLDER SEAL


    A060180E01
  1. Using a small screwdriver, remove the holder seal by prying the portion between the holder seal and the cutout part of the cylinder head.



17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    G034877E01
  1. Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.



18. REMOVE CAMSHAFT TIMING PULLEY


    A060182E01
  1. Remove the bolt of the camshaft timing pulley by holding the camshaft with a wrench.

    NOTICE:
    Make sure to remove the bolt of the camshaft timing pulley with the timing belt not installed.

  1. Remove the camshaft timing pulley.



19. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY


20. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts, nuts and timing belt cover.



21. REMOVE CYLINDER BLOCK INSULATOR (w/ EGR Cooler)


    A149941
  1. Remove the cylinder block insulator from the head.



22. REMOVE INJECTOR ASSEMBLY


A061112E01
  1. Remove the union bolt, 4 hollow screws, 5 gaskets and nozzle leakage pipe.

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



    G034876E01
  1. Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring and back-up ring from the injector.

  1. Remove the 4 injection nozzle sheets from the cylinder head.



23. REMOVE CAMSHAFT


    A060148E02
  1. Face the key groove of the camshaft upward by turning the camshaft with a wrench.



    A060147E01
  1. Uniformly loosen the 15 bearing cap bolts in several passes in the sequence shown in the illustration.

  1. Remove the 5 bearing caps, oil seal and 2 camshafts.



24. REMOVE CYLINDER HEAD SUB-ASSEMBLY


A059194E01
  1. Uniformly loosen and remove the 18 cylinder head bolts in several passes in the sequence shown in the illustration.

    NOTICE:
    Head warpage or cracking could result from removing bolts in the incorrect order.

  1. Lift the cylinder head from the dowels on the cylinder block, and place the cylinder head on wooden blocks on a bench.

    HINT:
    If the cylinder head is difficult to lift, use a screwdriver to pry between the cylinder head and block.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.



25. REMOVE CYLINDER HEAD GASKET