OIL PUMP (w/ EGR Cooler) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
![]() |
Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.
Loosen the cylinder block drain cock plug.

| 3. REMOVE ENGINE ASSEMBLY |
Remove the engine (Click here).
| 4. REMOVE FUEL INLET PIPE SUB-ASSEMBLY |
![]() |
Remove the bolt and clamp.
![]() |
Remove the bolt and oil level gauge guide.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
| 5. REMOVE EGR COOLER WITH ELECTRIC EGR CONTROL VALVE AND NO. 2 EGR VALVE |
Remove the EGR cooler (Click here).
| 6. REMOVE NO. 4 INJECTION PIPE |
![]() |
Remove the bolt and disconnect the injection pipe clamp.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
| 7. REMOVE VENTILATION PIPE |
![]() |
Remove the bolt and ventilation pipe.
| 8. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
| 9. REMOVE TIMING BELT |
Remove the timing belt (Click here).
| 10. REMOVE CAMSHAFT TIMING PULLEY |
![]() |
Remove the bolt of the camshaft timing pulley by holding the camshaft with a wrench.
Remove the camshaft timing pulley.
| 11. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY |
| 12. REMOVE CYLINDER BLOCK INSULATOR |
![]() |
Remove the cylinder block insulator from the head.
| 13. REMOVE NO. 2 TIMING BELT COVER |
Remove the 4 bolts, nuts and timing belt cover.
| 14. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the 2 nuts, 5 bolts, water pump and gasket.
| 15. REMOVE TIMING GEAR COVER INSULATOR |
![]() |
Remove the bolt and gear cover insulator.
| 16. REMOVE VACUUM PUMP ASSEMBLY |
![]() |
Disconnect the vacuum hose.
Remove the 2 nuts, vacuum pump and O-ring.
| 17. REMOVE VANE PUMP ASSEMBLY |
Remove the 2 nuts, vane pump and O-ring.
| 18. REMOVE PUMP DRIVE SHAFT PULLEY |
![]() |
Remove the 4 bolts, No. 2 camshaft timing pulley flange and pump drive shaft pulley.
![]() |
Using SST, hold the crankshaft pulley and remove the nut and O-ring.
| 19. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, remove the pulley bolt.
![]() |
Using SST, remove the pulley.
| 20. REMOVE CRANKSHAFT POSITION SENSOR |
Disconnect the sensor connector.
Remove the 3 clips, bolt and sensor.

| 21. REMOVE CAMSHAFT POSITION SENSOR |
![]() |
Disconnect the sensor connector.
Remove the bolt and sensor.
| 22. REMOVE TIMING GEAR COVER |
![]() |
Remove the wire harness clamp.
Remove the 14 bolts and 2 nuts.
Using a slotted screwdriver, gently separate the cover from the timing gear case.
Remove the cover and O-ring.
| 23. FIX NO. 1 IDLE GEAR |
![]() |
Fix the sub idle gears to the idle gear with the service bolt.
| 24. REMOVE CRANKSHAFT TIMING GEAR |
![]() |
Remove the No. 1 crankshaft position sensor plate.
![]() |
Using SST, remove the crankshaft timing gear.
| 25. REMOVE NO. 1 IDLE GEAR |
![]() |
Remove the 2 bolts, idle gear thrust plate.
Remove the service bolt and idle gear.
Remove the No. 1 idle gear shaft.
| 26. REMOVE INJECTION GEAR |
![]() |
Using SST, remove the injection gear.
| 27. REMOVE FUEL SUPPLY PUMP ASSEMBLY |
![]() |
Disconnect the 2 fuel hoses.
![]() |
Disconnect the 2 connectors.
![]() |
Remove the 4 bolts indicated by the arrows in the illustration.
Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.
![]() |
Remove the set nut and O-ring while holding the crankshaft pulley by using SST.
![]() |
Loosen the 2 nuts.
![]() |
Using SST, disconnect the pump from the injection gear.
Remove the 2 nuts and pump.
Remove the O-ring.
| 28. REMOVE OIL DIPSTICK GUIDE |
![]() |
Remove the bolt and injection pipe clamp.
Remove the bolt and guide.
Remove the O-ring from the guide.
| 29. REMOVE OIL PAN SUB-ASSEMBLY |
Remove the 22 bolts and 2 nuts.
![]() |
Insert the blade of a oil pan seal cutter between the cylinder block and oil pan. Cut through the applied sealer and remove the oil pan.
Remove the 2 bolts, nut, oil strainer and gasket.
Clean off any sealer remaining the oil pan and cylinder block.
| 30. REMOVE TIMING GEAR CASE ASSEMBLY |
![]() |
Remove the 8 bolts and union bolt. Then remove the timing gear case and its 2 O-rings.
Remove the nut and No. 1 vacuum transmitting pipe.
Remove the oil pump gasket.