Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    42    Air Inlet Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

Recirculation of fresh air is controlled as follows:
The damper servo (air inlet damper servo motor) sends the air inlet damper position as a pulse signal to the air conditioning amplifier. Then the air conditioning amplifier uses the pulse signal to determine how much the servo motor should be rotated forward/backward, and moves the air inlet damper to the appropriate position.

HINT:
This DTC is also output if the damper and damper link are malfunctioning or unable to move properly. When this DTC is output, confirm that the mechanical parts of the damper and damper link are not defective or damaged.


DTC Code
Detection Item
Trouble Area
42
Air inlet damper control servo motor activation request signal is output, but servo motor position data does not change or is inaccurate
  1. Damper servo sub-assembly (Air inlet damper servo motor)
  2. Harness or connector
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E170955E04


INSPECTION PROCEDURE

1.PERFORM ACTUATOR CHECK
  1. Remove the glove box to visually check the damper servo (air inlet damper servo motor) operation.

  1. Enter actuator check mode (Click here).

  1. Press the DEF switch to change to the step operation (Click here).

  1. Press the DEF switch to check the operation of the damper servo (air inlet damper servo motor).
    Display Code
    Air Inlet Control Damper Position
    0
    FRESH
    1
    FRESH
    2
    RECIRCULATION/FRESH
    (50%)
    3
    RECIRCULATION
    4
    RECIRCULATION
    5
    FRESH
    6
    FRESH
    7
    RECIRCULATION
    8
    FRESH
    9
    FRESH

    OK:
    Air inlet control damper position changes in accordance with each display code.

    Result 
    Result
    Proceed to
    OK (Checking from the PROBLEM SYMPTOMS TABLE)
    A
    OK (Checking from the DTC)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (DAMPER SERVO - AIR CONDITIONING AMPLIFIER)


    E170956E08
  1. Disconnect the D15 servo connector.

  1. Disconnect the A38 and A37 amplifier connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D15-5*1 - A37-22 (AIR)
    D15-4*2 - A37-22 (AIR)
    Always
    Below 1 Ω
    D15-4*1 - A37-23 (AIF)
    D15-5*2 - A37-23 (AIF)
    D15-2 - A38-17 (PIA)
    D15-3 - A38-16 (PIB)
    D15-1 - A38-21 (SG-7)
    D15-4 - Body ground
    Always
    10 kΩ or higher
    D15-5 - Body ground
    D15-2 - Body ground
    D15-3 - Body ground
    D15-1 - Body ground

    1. *1: for LHD
    2. *2: for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK DAMPER SERVO SUB-ASSEMBLY (AIR INLET DAMPER SERVO MOTOR)
  1. Check if the malfunction disappears when a normally functioning damper servo (air inlet damper servo motor) is installed.

    OK:
    Air inlet control damper operates normally.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

REPLACE DAMPER SERVO SUB-ASSEMBLY (AIR INLET DAMPER SERVO MOTOR)