Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

DTC    P0122    Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

DTC    P0123    Throttle / Pedal Position Sensor / Switch "A" Circuit High Input

for Preparation Click here


DESCRIPTION

The throttle position sensor is mounted on the diesel throttle body and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.
The ECM determines the vehicle's driving conditions from the signals input to its VLU terminal. The data is one of the inputs used for EGR control, etc.

G037167E06


DTC No.
DTC Detection Condition
Trouble Area
P0122
Throttle position sensor output (VLU) is less than 0.2 V
(1 trip detection logic)
  1. Throttle position sensor
  2. Open or short in VLU circuit
  3. Open in VC circuit
  4. ECM
P0123
Throttle position sensor output (VLU) is more than 4.8 V
(1 trip detection logic)
  1. Throttle position sensor
  2. Open in E2 circuit
  3. VC and VLU circuits are short-circuited
  4. ECM

MONITOR DESCRIPTION

When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

G037166E05


WIRING DIAGRAM


A154311E03


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If different DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)


    G038772E18
  1. Disconnect the E7 and E8 ECM connectors.

  1. Disconnect the T2 throttle position sensor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VC (E8-18) - VC (T2-1)
    Below 1 Ω
    VLU (E7-29) - VAF (T2-3)
    Below 1 Ω
    E2 (E8-28) - E2 (T2-2)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VC (E8-18) or VC (T2-1) - Body ground
    10 kΩ or higher
    VLU (E7-29) or VAF (T2-3) - Body ground
    10 kΩ or higher
    E2 (E8-28) or E2 (T2-2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT ECM (VC VOLTAGE)


    C129053E07
  1. Disconnect the T2 throttle position sensor connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the throttle position sensor connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    VC (T2-1) - E2 (T2-2)
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK


3.REPLACE DIESEL THROTTLE BODY ASSEMBLY
Replace diesel throttle body assembly (Click here).

NEXT


4.CHECK IF DTC OUTPUT RECURS
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Let the engine idle for 60 seconds.

  1. Repeat quick engine revving to 2,500 rpm for 30 seconds.

  1. Check for DTC(s).

    Result:

    Display (DTC Output)
    Proceed to
    P0122 and/or P0123
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)