FUEL INJECTOR (w/ EGR Cooler) > INSTALLATION |
| 1. INSTALL INJECTOR ASSEMBLY |
![]() |
Install 4 new injection nozzle sheets to the cylinder head.
Apply a light amount of clean engine oil to 4 new O-rings.
![]() |
Install the O-ring to each injector as shown in the illustration.
Insert the 4 injectors into the cylinder head.
Register injector compensation code (when replacing with a new injector).
![]() |
Temporarily install 4 new washers and the 4 nozzle clamps with the 4 clamp bolts.

Temporarily install the 4 injection pipes with the union nuts.
![]() |
Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces.
If scratches or dents are present, replace the nozzle leakage pipe.
![]() |
Set the leakage pipe and 5 new gaskets in place.
![]() |
Temporarily install the leakage pipe with the 4 hollow screws and union bolt.
Tighten the 4 holder clamp bolts.
![]() |
Tighten the 4 hollow screws in order from 1 to 4.
Tighten the union bolt.
Remove the 4injection pipes and union nuts.
| 2. CHECK FOR FUEL LEAK |
![]() |
Check that there are no leaks from the nozzle leakage pipe connection.
Install the gasket and No. 2 nozzle leakage pipe to the cylinder head with SST (check valve).
Apply a light amount of soapy water (or other fluid for detecting fuel leakage) on the nozzle leakage pipe connection.
![]() |
Install SST (turbocharger pressure gauge) to the fuel return side of the leakage pipe, and maintain 100 kPa (1.0 kgf/cm2, 14.5 psi) of pressure for 60 seconds to check that no bubbles form.
After checking for fuel leaks, wipe off the soapy water from the leakage pipe connection.
Remove SST, the No. 2 nozzle leakage pipe and gasket.
| 3. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Remove any old seal packing (FIPG) material from the cylinder head.
![]() |
Apply seal packing to the specific areas shown in the illustration.
![]() |
Install the a new gasket and cylinder head cover with the 10 bolts and 2 nuts.
Install 4 new Nozzle holder seals.
Connect the ventilation hose.
![]() |
Connect the 4 connectors and install the 3 bolts.
| 4. INSTALL NO. 4 INJECTION PIPE |
![]() |
Temporarily install the No. 4 injection pipe with the union nuts.
Install new injection pipe clamp with the bolt.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a union nut wrench, tighten the injection pipe union nuts on the injector side.
| 5. INSTALL EGR COOLER ASSEMBLY |
Install the EGR cooler assembly (Click here).
| 6. INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE |
Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.
![]() |
Install the No. 2 and No. 3 injection pipe clamps with the 2 bolts and 2 nuts, as shown in the illustration.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 7. CHECK FOR INJECTOR COMPENSATION CODE |
Read the injector compensation code .
Check that compensation code of installed injector is same as code registered in ECM. If the code is not as specified, register the injector compensation code on the injector (Click here).
| 8. INSTALL INTERCOOLER ASSEMBLY |
Install the intercooler assembly (Click here).
| 9. ADD FUEL |
| 10. TIGHTEN FUEL TANK CAP ASSEMBLY |
| 11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 12. PERFORM REGISTRATION |
Perform registration of injector compensation codes .
Perform registration of pilot quantity learning .
| 13. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Start the engine.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| 14. REGISTER INJECTOR COMPENSATION CODE |
Register the injector compensation code (Click here).
| 15. CHECK FOR FUEL LEAKS |
| 16. CHECK FOR OIL LEAKS |