Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM (w/ VSC)

CAN COMMUNICATION SYSTEM (w/ VSC) > TERMINALS OF ECU


HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
    2. When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).


JUNCTION CONNECTOR


  1. NO. 1 JUNCTION CONNECTOR


    C190573E06


    No. 1 Junction Connector
    Wiring Color
    Connect to
    J54-4 (CANH)
    B
    No. 2 junction connector
    J54-1 (CANL)
    W
    J54-12 (CANH)
    B
    ECM
    J54-6 (CANL)
    W
    J54-13 (CANH)
    R
    Skid control ECU
    J54-7 (CANL)
    W



  2. NO. 2 JUNCTION CONNECTOR


    C190574E06


    No. 2 Junction Connector
    Wiring Color
    Connect to
    J53-1 (CANH)
    B
    No. 1 junction connector
    J53-2 (CANL)
    W
    J53-3 (CANH)
    B
    No. 3 junction connector
    J53-7 (CANL)
    W
    J53-4 (CANH)
    R
    Yaw rate sensor
    J53-6 (CANL)
    W



  3. NO. 3 JUNCTION CONNECTOR


    C190575E03


    Wiring Color 
    Junction Connector A Side
    Color (CANH Side)
    Color (CANL Side)
    No. 2 junction connector and ECM (J50)
    B
    W
    Steering angle sensor (J51)
    W
    R

    Wiring Color 
    Junction Connector B Side
    Color (CANH Side)
    Color (CANL Side)
    DLC3 (J49)
    W
    R


TERMINALS OF CONNECTORS FOR JUNCTION CONNECTOR
C135249
Terminal No.
Symbol
1
CANL
2
CANH

CHECK DLC3
H102621E26
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    W - R
    Ignition switch off
    54 to 69 Ω
    D1-6 (CANH) - D1-4 (CG)
    W - G
    Ignition switch off
    200 Ω or higher
    D1-14 (CANL) - D1-4 (CG)
    R - G
    Ignition switch off
    200 Ω or higher
    D1-6 (CANH) - D1-16 (BAT)
    W - G
    Ignition switch off
    6 kΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    R - G
    Ignition switch off
    6 kΩ or higher


CHECK SKID CONTROL ECU

C190577E05

  1. Disconnect the S35 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    S35-25 (CANH) - S35-14 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    S35-25 (CANH) - S35-1 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    S35-14 (CANL) - S35-1 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    S35-25 (CANH) - S35-12 (+BS)
    B - W-R
    Ignition switch off
    6 kΩ or higher
    S35-14 (CANL) - S35-12 (+BS)
    W - W-R
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 1KD-FTV, 2KD-FTV)

C190578E03

  1. Disconnect the E6 and E7 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    E6-24 (CANH) - E6-23 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    E6-24 (CANH) - E7-7 (E1)
    B - BR
    Ignition switch off
    200 Ω or higher
    E6-23 (CANL) - E7-7 (E1)
    W - BR
    Ignition switch off
    200 Ω or higher
    E6-24 (CANH) - E6-2 (BATT)
    B - L
    Ignition switch off
    6 kΩ or higher
    E6-23 (CANL) - E6-2 (BATT)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK STEERING ANGLE SENSOR

C190672E04

  1. Disconnect the S37 sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    S37-4 (CANH) - S37-3 (CANL)
    W - R
    Ignition switch off
    54 to 69 Ω
    S37-4 (CANH) - S37-2 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    S37-3 (CANL) - S37-2 (ESS)
    R - W-B
    Ignition switch off
    200 Ω or higher
    S37-4 (CANH) - S37-6 (BAT)
    W - B
    Ignition switch off
    6 kΩ or higher
    S37-3 (CANL) - S37-6 (BAT)
    R - B
    Ignition switch off
    6 kΩ or higher


CHECK YAW RATE SENSOR

C190673E06

  1. Disconnect the Y1 sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    Y1-3 (CANH) - Y1-2 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    Y1-3 (CANH) - Y1-1 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    Y1-2 (CANL) - Y1-1 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    Y1-3 (CANH) - D1-16 (BAT)
    B - G
    Ignition switch off
    6 kΩ or higher
    Y1-2 (CANL) - D1-16 (BAT)
    W - G
    Ignition switch off
    6 kΩ or higher