CAN COMMUNICATION SYSTEM (w/ VSC) > Open in CAN Main Bus Line |
| Symptom | Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher. |
|

| 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
| NEXT | |
| 2.CHECK DLC3 |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Measured Resistance | Proceed to |
| D1-6 (CANH) - D1-14 (CANL) | Ignition switch off | 54 to 69 Ω | OK |
| 70 Ω or higher | NG |
|
| ||||
| OK | |
| 3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR) |
![]() |
Disconnect the J54 No. 1 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J54-4 (CANH) - J54-1 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | |
| 4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J54-12 (CANH) - J54-6 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 5.CONNECT CONNECTOR |
Reconnect the J54 No. 1 junction connector connector.
| NEXT | |
| 6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR) |
![]() |
Disconnect the J53 No. 2 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J53-3 (CANH) - J53-7 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | |
| 7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J53-1 (CANH) - J53-2 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 8.CONNECT CONNECTOR |
Reconnect the J53 No. 2 junction connector connector.
| NEXT | |
| 9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
![]() |
Disconnect the J50 No. 3 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J50-2 (CANH) - J50-1 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 10.CONNECT CONNECTOR |
Reconnect the J54 No. 1 junction connector connector.
| NEXT | |
| 11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 1 JUNCTION CONNECTOR) |
![]() |
Disconnect the E6 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E6-24 (CANH) - E6-23 (CANL) | Ignition switch off | 108 to 132 Ω |
| Result | Proceed to |
| OK (for 1KD-FTV) | A |
| OK (for 2KD-FTV) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||