Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1268/68    Transfer "L4" Position Switch Circuit

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
C1268/68
No signal is input to the EXI4 terminal of the skid control ECU.
  1. L4 position switch (Transfer indicator switch No. 1)
  2. L4 position switch circuit
  3. Skid control ECU (Brake actuator assembly)
  4. Transmission control ECU assembly

WIRING DIAGRAM


C190841E04


C190842E03


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

1.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI4 TERMINAL)


    C160263E81
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S35-9 (EXI4) - Body ground
    1. Ignition switch ON
    2. Transfer shift position not L4
    11 to 14 V
    S35-9 (EXI4) - Body ground
    1. Ignition switch ON
    2. Transfer shift position L4
    Below 1.5 V



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTC is recorded.
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK
A

REPLACE BRAKE ACTUATOR ASSEMBLY 

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI4 TERMINAL)

C190365E03

  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU connector.

  1. for A/T:
    Disconnect the transmission control ECU connector.

  1. Disconnect the L4 position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-9 (EXI4) - T4-1
    Always
    Below 1 Ω
    S35-9 (EXI4) - Body ground
    Always
    10 kΩ or higher
    T4-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT L4 POSITION SWITCH (TRANSFER INDICATOR SWITCH NO. 1)


    C190634E01
  1. Remove the L4 position switch (transfer indicator switch No. 1) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    1 - 2
    Free
    10 kΩ or higher



NG
REPLACE TRANSFER INDICATOR SWITCH NO. 1
OK


5.CHECK HARNESS AND CONNECTOR (L4 POSITION SWITCH POWER SOURCE CIRCUIT)


    C190367E02
  1. Turn the ignition switch off.

  1. Disconnect the L4 position switch connector.

  1. Disconnect the skid control ECU connector.

  1. for A/T:
    Connect the transmission control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Ignition switch ON
    11 to 14 V

    Result 
    Result
    Proceed to
    OK
    A
    NG (for M/T)
    B
    NG (for A/T)
    C



B
REPAIR OR REPLACE HARNESS OR CONNECTOR

C
Go to step 6
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) 

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TRANSMISSION CONTROL ECU)

C190366E02

  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU connector.

  1. Disconnect the transmission control ECU connector.

  1. Disconnect the L4 position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-9 (EXI4) - T18-15 (L4)
    Always
    Below 1 Ω
    S35-9 (EXI4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY