Home › BODY › SEAT › FRONT POWER SEAT MOTOR ASSEMBLY (for Slide)

FRONT POWER SEAT MOTOR ASSEMBLY (for Slide) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

NOTICE:
If the rear power seat motor has been dropped, replace it with a new one.



1. INSTALL FRONT POWER SEAT MOTOR ASSEMBLY (for Slide)


    B207458
  1. Install the slide cable.

    NOTICE:
    Make sure that the cable is correctly inserted into the motor.



    B206612E01
  1. Install the front power seat motor assembly with slide cable to the slide screws.

    NOTICE:
    1. Make sure that the slide rail is locked in the rearmost position.
    2. If the serrations on the slide screw and front power seat motor assembly with slide cable do not align, grip the slide screw with needle-nose pliers and install the front power seat motor assembly with slide cable while slightly moving the slide screw. In these cases, do not turn the slide screw 90° or more.
    3. Do not apply excessive force to the slide cable (do not bend the slide cable 60° or more).

  1. Using a 4 mm socket hexagon wrench, install the 4 bolts.

    Torque:
    1.6 N*m{ 16 kgf*cm , 14 in.*lbf }

  1. Using a 5 mm socket hexagon wrench, install the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    B207101
  1. Install new 2 nuts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }

  1. Attach the claw to connect the connector to the seat frame.



    B108592
  1. Connect the positive (+) battery terminal to terminal 1 of the power seat motor and the negative (-) battery terminal to terminal 2, and then slide the seat and align the matchmarks.



    B206610
  1. Check that the matchmarks are aligned on both sides.
    If the matchmarks are not aligned, check the installation condition of the power seat motor assembly, and remove and reinstall the power seat motor assembly if necessary.

  1. Connect the connector.



    B206614
  1. Install the seat cushion frame with the 4 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



    B207524
  1. Attach the 4 clamps indicated by the arrows in the illustration to install the seat cushion spring.

  1. Attach the 2 wire harness clamps.



2. INSTALL SEAT CUSHION COVER WITH PAD
  1. Set the seat cushion cover with pad in place.



  1. Attach the hooks to install the seat cushion cover with pad.


    B207449



    B207083E01
  1. Using hog ring pliers, attach the rubber bands of the seatback cover to the seat frame with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



3. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH


B120318
  1. Install the buckle cover on the seat belt.



    B087821E01
  1. Attach the wire harness to the clamp.

  1. Install the seat belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding part of the seat adjuster.



    B087811E01
  1. Attach the clamp as shown in the illustration.



4. INSTALL FRONT SEAT CUSHION INNER SHIELD RH


  1. Pass the wire harness of the front seat inner belt assembly below the claw and into the front seat cushion inner shield.


    B207196



    B207618
  1. Attach the claw to temporarily install the cushion inner shield.

    NOTICE:
    Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat cushion inner shield.



    B207198
  1. Attach the guide and claw.

    NOTICE:
    Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat cushion inner shield.

  1. Install the screw to the cushion inner shield.



5. INSTALL FRONT POWER SEAT SWITCH


    B207080
  1. Connect the connector.

  1. Install the switch with the 3 screws.



6. INSTALL FRONT SEAT CUSHION SHIELD RH


    B207039
  1. Attach the claw and guide to install the cushion shield.

  1. Install the 3 screws.



    B207078
  1. Install the 2 screws.



7. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    B207446
  1. Attach the 4 claws to install the knob.



8. INSTALL RECLINING POWER SEAT SWITCH KNOB


    B207447
  1. Attach the 2 claws to install the knob.



9. INSTALL FRONT SEAT ASSEMBLY
  1. Install the front seat assembly (Click here).



10. INSPECT FRONT SEAT ASSEMBLY
  1. Check the power seat operation (Click here).