Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C0200/31    Front Speed Sensor RH Circuit

DTC    C0205/32    Front Speed Sensor LH Circuit

DTC    C1271/71    Low Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC    C1272/72    Low Output Signal of Front Speed Sensor LH (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU. The speed sensor has a magnet behind its detection terminal, and detects changes in magnetic flux density between the peaks and valleys of the magnetic rotor teeth.
The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU. The ECU monitors the wheel speeds through these pulse signals to control the ABS.
DTCs C1271/71 and C1272/72 are deleted when the speed sensor sends a vehicle speed signal or Test Mode ends. DTCs C1271/71 and C1272/72 are output only in Test Mode.

HINT:
When the connectors between the speed sensor and skid control ECU are connected, the following waveform is output.


C172023E14


DTC Code
DTC Detection Condition
Trouble Area
C0200/31
C0205/32
When one of the following conditions is met:
  1. At a vehicle speed of 10 km/h (6 mph) or more, an open or short in the sensor signal circuit continues for 1 second or more.
  2. Momentary interruption of the sensor signal occurs 255 times or more.
  3. An open in the speed sensor signal circuit continues for 0.5 seconds or more.
  4. With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases and stays at or below a certain value for 0.5 seconds or more.
  1. Front speed sensor RH/LH
  2. Speed sensor circuit
  3. Front skid control rotor RH/LH
  4. Sensor installation
  5. Skid control ECU (Brake actuator assembly)
C1271/71
C1272/72
Detected only during Test Mode.
  1. Front speed sensor RH/LH
  2. Sensor installation
  3. Front skid control rotor RH/LH

HINT:
  1. DTCs C0200/31 and C1271/71 are for the front speed sensor RH.
  2. DTCs C0205/32 and C1272/72 are for the front speed sensor LH.


WIRING DIAGRAM


C149728E28


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (Click here).
  2. Check the speed sensor signal in test mode after replacing parts or clearing DTCs (Click here).

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harnesses and connectors corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    Front speed sensor RH open detection / Error or Normal
    Normal
    -
    FL Speed Open
    Front speed sensor LH open detection / Error or Normal
    Normal
    -

    OK:
    Normal (There are no momentary interruptions.)

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 5
OK


2.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front wheel RH speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar to speed indicated on speedometer
    FL Wheel Speed
    Front wheel LH speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar to speed indicated on speedometer

  1. Check that there is no significant difference between the speed value displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output displayed on the intelligent tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 7
OK


3.PERFORM TEST MODE (SIGNAL CHECK)
  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are erased.



NG
Go to step 7
OK


4.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 30 km/h (19 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
Go to step 12
A

CHECK FOR INTERMITTENT PROBLEMS 

5.CHECK IF SKID CONTROL ECU AND FRONT SPEED SENSOR CONNECTORS ARE SECURELY CONNECTED
  1. Check if the skid control ECU and front speed sensor connectors are securely connected.


NEXT


6.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 30 km/h (19 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


7.CHECK FRONT SPEED SENSOR INSTALLATION


    I044006E17
  1. Turn the ignition switch off.

  1. Check the speed sensor installation (Click here).

    OK:
    The installation bolt is tightened properly and there is no clearance between the speed sensor and knuckle.



NG
INSTALL FRONT SPEED SENSOR CORRECTLY
OK


8.CHECK FRONT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    HINT:
    1. If the sensor is contaminated with oil or other foreign material, clean the sensor.
    2. If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.

    NOTICE:
    1. Do not replace the speed sensor if no damage to the speed sensor tip is found.
    2. Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


9.INSPECT FRONT SPEED SENSOR


    C192853E02
  1. Install the front speed sensor.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    1 (FR+) - Body ground
    Always
    10 kΩ or higher
    2 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    1 (FL+) - Body ground
    Always
    10 kΩ or higher
    2 (FL-) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE FRONT SPEED SENSOR
OK


10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)


  1. Disconnect the skid control ECU connector.


    C190590E02

  1. Disconnect the front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    S35-7 (FR+) - S5-1 (FR+)
    Always
    Below 1 Ω
    S35-7 (FR+) - Body ground
    Always
    10 kΩ or higher
    S35-6 (FR-) - S5-2 (FR-)
    Always
    Below 1 Ω
    S35-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    S35-19 (FL+) - S4-1 (FL+)
    Always
    Below 1 Ω
    S35-19 (FL+) - Body ground
    Always
    10 kΩ or higher
    S35-18 (FL-) - S4-2 (FL-)
    Always
    Below 1 Ω
    S35-18 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.INSPECT SKID CONTROL ECU (SENSOR INPUT)
  1. Connect the skid control ECU connector.



    C190626E01
  1. Disconnect the front speed sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH:
    Tester Connection
    Switch Condition
    Specified Condition
    S5-1 (FR+) - Body ground
    Ignition switch ON
    8 to 14 V
    for LH:
    Tester Connection
    Switch Condition
    Specified Condition
    S4-1 (FL+) - Body ground
    Ignition switch ON
    8 to 14 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


12.REPLACE FRONT SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the front speed sensor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


13.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


14.REPLACE FRONT SKID CONTROL ROTOR
  1. Turn the ignition switch off.

  1. Replace the front skid control rotor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


15.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY
A

END