VEHICLE STABILITY CONTROL SYSTEM > TEST MODE PROCEDURE |
| WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK |
Release the parking brake.
![]() |
When the ignition switch is turned to ON, check that the ABS warning, brake warning, VSC OFF indicator, and slip indicator lights come on for approximately 3 seconds.
| Trouble Area | See procedure |
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| Brake warning light circuit (Remains on) |
Click here
|
| Brake warning light circuit (Does not come on) |
Click here
|
| VSC OFF indicator light circuit (Remains on) |
Click here
|
| VSC OFF indicator light circuit (Does not come on) |
Click here
|
| Slip indicator light circuit (Remains on) |
Click here
|
| Slip indicator light circuit (Does not come on) |
Click here
|
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using Intelligent Tester) |
Procedure to enter Test Mode
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
for A/T:
Check that the shift lever is in the P position and apply the parking brake.
for M/T:
Check that the shift lever is in neutral and apply the parking brake.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Switch the skid control ECU to Test Mode using the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / Signal Check.
![]() |
Check that the ABS warning and VSC OFF indicator lights come on for several seconds and then blink in the Test Mode blinking pattern.
Lost Booster Pressure Judgment Check and Master Cylinder Pressure Sensor Zero Point Calibration
Turn the ignition switch to ON.
Check that the brake warning light comes on when depressing the brake pedal with a force greater than 59 N (6 kgf, 13.2 lbf) for 1 second or more. (The lost booster pressure state is judged as normal.)
While depressing the brake pedal with a force greater than 59 N (6 kgf, 13.2 lbf), start the engine.
Check that the brake warning light goes off when quickly releasing the brake pedal. (The lost booster pressure state is judged as normal.)
Leave the vehicle for 1 second or more. (Master cylinder pressure sensor zero point calibration)
Acceleration Sensor Check
Keep the vehicle stationary on a level surface for 1 second or more.
Master Cylinder Pressure Sensor Check
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and then quickly and continuously depress the brake pedal with a force greater than 98 N (10 kgf, 22 lbf) for 1 second.
Check that the ABS warning light stays on for 3 seconds.
4WD Detection Switch Signal Check
Move the transfer high and low shift lever to H4 or L4 to put the vehicle in 4WD mode.
Move the transfer high and low shift lever to H2 to put the vehicle in 2WD mode.
Speed Sensor Check
![]() |
Check that the ABS warning light is blinking as shown in the illustration.
Check the speed sensor signal.

![]() |
Check that the VSC OFF indicator light is blinking in the Test Mode blinking pattern.
Yaw Rate Sensor Check
Keep the vehicle in a stationary condition on a level surface for 1 second or more.
![]() |
Drive the vehicle at a speed of approximately 5 km/h (3 mph), and turn the steering wheel either to the left or right 90° or more until the vehicle makes a 180° turn.
for A/T:
Stop the vehicle, move the shift lever to the P position and apply the parking brake. Check that the skid control buzzer sounds for 3 seconds.
for M/T:
Stop the vehicle, move the shift lever to neutral and apply the parking brake. Check that the skid control buzzer sounds for 3 seconds.
VSC OFF Switch Check
Briefly press the VSC OFF switch.
Check that the slip indicator light goes off.
Briefly press the VSC OFF switch again to turn the slip indicator light on.
End of Sensor Check.
![]() |
If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle is stopped and goes off while the vehicle is driven.
Read Sensor Check DTCs.
Read the DTC(s) by following the tester screen.
Turn the ignition switch off and disconnect the intelligent tester.
Sensor Check DTCs
| DTC Code | Detection Item | Trouble Area |
| C1271 | Low Output Signal of Front Speed Sensor RH |
|
| C1272 | Low Output Signal of Front Speed Sensor LH |
|
| C1273 | Low Output Signal of Rear Speed Sensor RH |
|
| C1274 | Low Output Signal of Rear Speed Sensor LH |
|
| C1275 | Abnormal Change in Output Signal of Front Speed Sensor RH | Front skid control rotor RH |
| C1276 | Abnormal Change in Output Signal of Front Speed Sensor LH | Front skid control rotor LH |
| C1277 | Abnormal Change in Output Signal of Rear Speed Sensor RH | Rear skid control rotor RH |
| C1278 | Abnormal Change in Output Signal of Rear Speed Sensor LH | Rear skid control rotor LH |
| C1279 | Acceleration Sensor Output Voltage Malfunction |
|
| C1281 | Master Cylinder Pressure Sensor Output Malfunction |
|
| C1282 | Center differential lock position switch malfunction |
|
| DTC Code | Detection Item | Trouble Area |
| C0371 | Yaw Rate Sensor | Yaw rate and acceleration sensor (Yaw rate sensor assembly) |
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When not Using Intelligent Tester) |
Procedure to enter Test Mode
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
for A/T:
Check that the shift lever is in the P position and apply the parking brake.
for M/T:
Check that the shift lever is in neutral and apply the parking brake.
![]() |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
![]() |
Check that the ABS warning and VSC OFF indicator lights come on for several seconds and then blink in the Test Mode blinking pattern.
Lost Booster Pressure Judgment Check and Master Cylinder Pressure Sensor Zero Point Calibration
Turn the ignition switch to ON.
Check that the brake warning light comes on when depressing the brake pedal with a force greater than 59 N (6 kgf, 13.2 lbf) for 1 second or more. (The lost booster pressure state is judged as normal.)
While depressing the brake pedal with a force greater than 59 N (6 kgf, 13.2 lbf), start the engine.
Check that the brake warning light goes off when quickly releasing the brake pedal. (The lost booster pressure state is judged as normal.)
Leave the vehicle for 1 second or more. (Master cylinder pressure sensor zero point calibration)
Acceleration Sensor Check
Keep the vehicle stationary on a level surface for 1 second or more.
Master Cylinder Pressure Sensor Check
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and then quickly and continuously depress the brake pedal with a force greater than 98 N (10 kgf, 22 lbf) for 1 second.
Check that the ABS warning light stays on for 3 seconds.
4WD Detection Switch Signal Check
Move the transfer high and low shift lever to H4 or L4 to put the vehicle in 4WD mode.
Move the transfer high and low shift lever to H2 to put the vehicle in 2WD mode.
Speed Sensor Check
![]() |
Check that the ABS warning light is blinking as shown in the illustration.
Check the speed sensor signal.

![]() |
Check that the VSC OFF indicator light is blinking in the Test Mode blinking pattern.
Yaw Rate Sensor Check
Keep the vehicle in a stationary condition on a level surface for 1 second or more.
![]() |
Drive the vehicle at a speed of approximately 5 km/h (3 mph), and turn the steering wheel either to the left or right 90° or more until the vehicle makes a 180° turn.
for A/T:
Stop the vehicle, move the shift lever to the P position and apply the parking brake. Check that the skid control buzzer sounds for 3 seconds.
for M/T:
Stop the vehicle, move the shift lever to neutral and apply the parking brake. Check that the skid control buzzer sounds for 3 seconds.
VSC OFF Switch Check
Briefly press the VSC OFF switch.
Check that the slip indicator light goes off.
Briefly press the VSC OFF switch again to turn the slip indicator light on.
End of Sensor Check
![]() |
If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle is stopped and goes off while the vehicle is driven.
Read Sensor Check DTCs.
![]() |
Using SST, connect terminals 12 (TS), 13 (TC) and 4 (CG) of the DLC3.
Count the number of blinks of the ABS warning and VSC OFF indicator lights.

After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3 and turn the ignition switch off.
Turn the ignition switch to ON.
Sensor Check DTCs
| DTC Code | Detection Item | Trouble Area |
| 71 | Low Output Signal of Front Speed Sensor RH |
|
| 72 | Low Output Signal of Front Speed Sensor LH |
|
| 73 | Low Output Signal of Rear Speed Sensor RH |
|
| 74 | Low Output Signal of Rear Speed Sensor LH |
|
| 75 | Abnormal Change in Output Signal of Front Speed Sensor RH | Front skid control rotor RH |
| 76 | Abnormal Change in Output Signal of Front Speed Sensor LH | Front skid control rotor LH |
| 77 | Abnormal Change in Output Signal of Rear Speed Sensor RH | Rear skid control rotor RH |
| 78 | Abnormal Change in Output Signal of Rear Speed Sensor LH | Rear skid control rotor LH |
| 79 | Acceleration Sensor Output Voltage Malfunction |
|
| 81 | Master Cylinder Pressure Sensor Output Malfunction |
|
| 82 | Center differential lock position switch malfunction |
|
| DTC Code | Detection Item | Trouble Area |
| 71 | Yaw Rate Sensor | Yaw rate and acceleration sensor (Yaw rate sensor assembly) |