Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

DTC    P0299    Turbocharger / Supercharger Underboost

DTC    P1251    Turbocharger / Supercharger Overboost Condition (Too High)

for Preparation Click here


DESCRIPTION

HINT:
Refer to DTC P0046 .


DTC No.
DTC Detection Condition
Trouble Area
P0299
The turbocharger boost pressure is 25 to 40 kPa (187 mmHg, 7.3 in.Hg to 300 mmHg, 11.8 in.Hg)* below the Target Boost Pressure for continues more than fixed time.
(2 trip detection logic)
*: This changes depending on the engine speed.
  1. Turbocharger sub-assembly
  2. Turbo motor driver
  3. Turbo motor driver power source
  4. Manifold absolute pressure sensor
  5. MAF meter
  6. EGR valve assembly
  7. Exhaust system and intake system are modified or clogged
  8. ECM
P1251
The turbocharger boost pressure is 223 kPa (1679 mmHg, 65.8 in.Hg) or more for 5 seconds or more.
(1 trip detection logic)
  1. Turbocharger sub-assembly
  2. Turbo motor driver
  3. Turbo motor driver power source
  4. Manifold absolute pressure sensor
  5. MAF meter
  6. EGR valve assembly
  7. Exhaust system and intake system are modified or clogged
  8. EGR passage
  9. Injector
  10. ECM

WIRING DIAGRAM

Refer to DTC P0046 .
Refer to DTC P1264 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0299 AND /OR P1251)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0299 and/or P1251
    A
    P0299 and/or P1251 and other DTCs
    B



B
GO TO RELEVANT DTC CHART (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (MAP)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and warm it up. Turn the intelligent tester ON.

  1. Enter the following menu: Powertrain / Engine and ECT / Data List / MAP.

    Standard:
    Item
    Condition*
    Reference Value
    MAP
    Ignition switch ON
    Same as atmospheric pressure
    MAP
    Idling
    95 to 105 kPa
    (713 to 788 mmHg, 28.1 to 31 in.Hg)
    MAP
    3000 rpm (no engine load)
    100 to 125 kPa
    (750 to 938 mmHg, 29.5 to 36.9 in.Hg)

    HINT:
    *: If no idling conditions are specified, the A/C switch and all accessory switches should be OFF with a fully warm engine.



NG
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
OK


3.CHECK EXHAUST SYSTEM
  1. Turn the ignition switch ON.

  1. Check the exhaust pipe for leaks.

    OK:
    Exhaust pipe has no leaks.



NG
REPAIR EXHAUST GAS LEAK
OK


4.CHECK AIR CLEANER FILTER
  1. Check that the air cleaner filter is not clogged.

    OK:
    Air cleaner filter is not clogged.



NG
REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
OK


5.CHECK INTAKE SYSTEM
  1. Disconnect the air cleaner hose.

  1. Use a mirror to visually check the turbocharger for any mechanical problems.

  1. When the engine is cold, check that the impeller of the turbocharger rotates smoothly, and perform a contact check to confirm whether there is any damage on it.

    OK:
    Impeller of turbocharger rotates smoothly.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


6.INSPECT TURBOCHARGER SUB-ASSEMBLY
  1. Check the turbocharger sub-assembly (Click here).



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
OK


7.CHECK ECM (VNTI VOLTAGE)
G036520E10
  1. While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

    Standard voltage:
    Tester Connection
    Specified Condition
    E8-17 (VNTI) - E7-7 (E1)
    Correct waveform is shown

    Tool Setting
    Condition
    2 V/DIV., 20 msec./DIV.
    Idling with warm engine



NG
REPLACE ECM (Click here)
OK


8.CHECK ECM (VNTO VOLTAGE)
A099245E10
  1. While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

    Standard voltage:
    Tester Connection
    Specified Condition
    E8-10 (VNTO) - E7-7 (E1)
    Correct waveform is shown

    Tool Setting
    Condition
    5 V/DIV., 20 msec./DIV.
    Idling with warm engine



NG
REPLACE TURBO MOTOR DRIVER
OK


9.CHECK EGR VALVE ASSEMBLY
  1. Check the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


10.INSPECT INTAKE AIR TEMPERATURE SENSOR
A114041E01
  1. Check the IAT sensor.

    1. Remove the MAF meter.

    2. Measure the resistance of the sensor.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      4 - 5
      -20°C (-4°F)
      13.6 to 18.4 kΩ
      4 - 5
      20°C (68°F)
      2.21 to 2.69 kΩ
      4 - 5
      60°C (140°F)
      0.49 to 0.67 kΩ



NG
REPLACE MASS AIR FLOW METER
OK

REPLACE ECM (Click here)