Home › ENGINE ยท 2TR-FE › FUEL › FUEL TANK (for Regular Cab Short Deck)

FUEL TANK (for Regular Cab Short Deck) > INSTALLATION

for Preparation Click here



1. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
  1. Apply a light coat of gasoline or grease to a new gasket, and install it to the fuel tank.

  1. Set the gauge tube to the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Put the retainer on the fuel tank. While holding the pump and gauge tube, tighten the retainer one complete turn by hand.



    A111069E04
  1. Using SST, tighten the retainer until the mark on the retainer aligns with mark A on the fuel tank, as shown in the illustration.

    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    HINT:
    1. If the alignment is difficult, make sure the mark on the retainer is within range B on the fuel tank.
    2. Fit the tips of SST onto the ribs of the retainer.



    A118171E01
  1. Install the 2 fuel tank tubes with the 2 tube joint clips.

    NOTICE:
    1. Check that there are no scratches or foreign objects on the connecting parts.
    2. Check that the fuel tube joints are inserted securely.
    3. Check that the tube joint clips are on the collars of the fuel tube joints.
    4. After installing the tube joint clips, check that the fuel tube joints have not been pulled off.



2. INSTALL NO. 1 FUEL TANK CUSHION


    A118155
  1. Install 3 new fuel tank cushions.



    A116052
  1. Install the heat insulator with 5 new clips.



3. INSTALL FUEL TANK ASSEMBLY
  1. Set the fuel tank on a mission jack.

  1. Lift up the mission jack.

  1. Connect the 4 harness clips and fuel pump connector to the fuel tank.

    NOTICE:
    Be careful not to cut the wirings.



    A118156E01
  1. Fold back the 2 cushion rubbers.

  1. Install the 3 fuel tank bands with the 3 pins and 3 clips.



    A118151
  1. Connect the 3 fuel tank bands with the 3 bolts.

    Torque:
    61 N*m{ 622 kgf*cm , 45 ft.*lbf }



4. INSTALL FUEL TANK FILLER PIPE
  1. Install the filler pipe with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



5. CONNECT FUEL TANK TO FILLER PIPE HOSE
  1. Connect the filler pipe hose to the fuel tank filler pipe.



6. CONNECT FUEL TANK BREATHER HOSE
  1. Connect the fuel tank breather hose to the fuel tank filler pipe.



7. CONNECT FUEL MAIN TUBE AND FUEL RETURN TUBE


G038855E01

NOTICE:
Before installing the tube connectors to the pipes, check the connectors for damage and foreign matter.



    A098610E04
  1. Connect the return tube connector to the pipe. Then connect the main tube connector to the pipe. Push the 2 parts together firmly until a "click" sound is heard.

    NOTICE:
    Check that the connectors and pipes are securely connected by trying to pull them apart.

  1. Connect the vent line hose.



8. INSTALL NO. 3 FUEL TUBE CLAMP


    G039253E01
  1. Install the tube clamp to the fuel tube.



9. INSTALL FUEL TANK CAP


10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


11. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



12. CHECK FOR FUEL LEAKS
  1. Connect the intelligent tester to the DLC3.

    1. Turn the ignition switch ON.

      NOTICE:
      Do not start the engine.

    2. Push the intelligent tester main switch ON.

    3. Select the Active Test and enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check for fuel leaks.

    1. Check that there are no fuel leaks after performing maintenance anywhere on the fuel system.