Home › BRAKE › BRAKE › BRAKE SYSTEM

BRAKE SYSTEM > PROBLEM SYMPTOMS TABLE

for Preparation Click here


HINT:
Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.


Brake system (2WD LHD) 
Symptom
Suspected Area
See page
Low pedal or spongy pedal
1. Fluid leaks in brake system
-
2. Air in brake system (TMT made)
Click here
3. Piston seals (worn or damaged, TMT made)
Click here
4. Rear brake shoe clearance (adjustment necessary)
Click here
5. Brake master cylinder (faulty, TMT made w/ ABS)
Click here
6. Brake master cylinder (faulty, TMT made w/o ABS)
Click here
7. Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
8. Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Brake drag
1. Brake pedal free play (minimal)
Click here
2. Parking brake shoe lever travel (adjustment necessary)
Click here
3. No. 1 parking brake wire (stuck)
Click here
4. No. 2 parking brake wire (stuck)
Click here
5. No. 3 parking brake wire (stuck)
Click here
6. Rear brake shoe clearance (adjustment necessary)
Click here
7. Pad (cracked or distorted, TMT made)
Click here
8. Lining (cracked or distorted)
Click here
9. Front brake piston (stuck or frozen, TMT made)
Click here
10. Rear brake piston (stuck or frozen)
Click here
11. Tension or return spring (faulty)
Click here
12. Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
13. Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
14. Vacuum leaks in booster system (TMT made)
Click here
15. Brake master cylinder (faulty, TMT made w/ ABS)
Click here
16. Brake master cylinder (faulty, TMT made w/o ABS)
Click here
Brake pull
1. Front brake piston (stuck or frozen, TMT made)
Click here
2. Rear brake piston (stuck or frozen)
Click here
3. Pad (oily, cracked or distorted, TMT made)
Click here
4. Lining (oily, cracked or distorted)
Click here
5. Disc (scored, TMT made)
Click here
Brake pedal is depressed firmly but brake is insufficient
1. Fluid leaks in brake system
-
2. Air in brake system (TMT made)
Click here
3. Pad (worn, cracked, distorted, oily or glazed, TMT made)
Click here
4. Lining (worn, cracked, distorted, oily or glazed)
Click here
5. Rear brake shoe clearance (adjustment necessary)
Click here
6. Disc (scored, TMT made)
Click here
7. Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
8. Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
9. Vacuum leaks in booster system (TMT made)
Click here
Noise from brakes
1. Pad (cracked, distorted, dirty or glazed, TMT made)
Click here
2. Lining (cracked, distorted, dirty or glazed)
Click here
3. Installation bolt (TMT made)
Click here
4. Disc (scored, TMT made)
Click here
5. Pad support plate (loose, TMT made)
Click here
6. Anchor, return or tension spring (faulty)
Click here
7. Anti squeal shim (damaged, TMT made)
Click here
8. Shoe hold down spring (damaged)
Click here

Brake system (2WD RHD) 
Symptom
Suspected Area
See page
Low pedal or spongy pedal
1. Fluid leaks in brake system
-
2. Air in brake system (TMT made)
Click here
3. Air in brake system (TSAM made)
Click here
4. Piston seals (worn or damaged, TMT made)
Click here
5. Piston seals (worn or damaged, TSAM made)
Click here
6. Rear brake shoe clearance (adjustment necessary)
Click here
7. Brake master cylinder (faulty, TMT made w/ ABS)
Click here
8. Brake master cylinder (faulty, TMT made w/o ABS)
Click here
9. Brake master cylinder (faulty, TSAM made w/ ABS)
Click here
10. Brake master cylinder (faulty, TSAM made w/o ABS)
Click here
11. Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
12. Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
13. Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
14. Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Brake drag
1. Brake pedal free play (minimal)
Click here
2. Parking brake shoe lever travel (adjustment necessary)
Click here
3. No. 1 parking brake wire (stuck)
Click here
4. No. 2 parking brake wire (stuck)
Click here
5. No. 3 parking brake wire (stuck)
Click here
6. Rear brake shoe clearance (adjustment necessary)
Click here
7. Pad (cracked or distorted, TMT made)
Click here
8. Pad (cracked or distorted, TSAM made)
Click here
9. Lining (cracked or distorted)
Click here
10. Front brake piston (stuck or frozen, TMT made)
Click here
11. Front brake piston (stuck or frozen, TSAM made)
Click here
12. Rear brake piston (stuck or frozen)
Click here
13. Tension or return spring (faulty)
Click here
14. Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
15. Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
16. Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
17. Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
18. Vacuum leaks in booster system (TMT made)
Click here
19. Vacuum leaks in booster system (TSAM made)
Click here
20. Brake master cylinder (faulty, TMT made w/ ABS)
Click here
21. Brake master cylinder (faulty, TMT made w/o ABS)
Click here
22. Brake master cylinder (faulty, TSAM made w/ ABS)
Click here
23. Brake master cylinder (faulty, TSAM made w/o ABS)
Click here
Brake pull
1. Front brake piston (stuck or frozen, TMT made)
Click here
2. Front brake piston (stuck or frozen, TSAM made)
Click here
3. Rear brake piston (stuck or frozen)
Click here
4. Pad (oily, cracked or distorted, TMT made)
Click here
5. Pad (oily, cracked or distorted, TSAM made)
Click here
6. Lining (oily, cracked or distorted)
Click here
7. Disc (scored, TMT made)
Click here
8. Disc (scored, TSAM made)
Click here
Brake pedal is depressed firmly but brake is insufficient
1. Fluid leaks in brake system
-
2. Air in brake system (TMT made)
Click here
3. Air in brake system (TSAM made)
Click here
4. Pad (worn, cracked, distorted, oily or glazed, TMT made)
Click here
5. Pad (worn, cracked, distorted, oily or glazed, TSAM made)
Click here
6. Lining (worn, cracked, distorted, oily or glazed)
Click here
7. Rear brake shoe clearance (adjustment necessary)
Click here
8. Disc (scored, TMT made)
Click here
9. Disc (scored, TSAM made)
Click here
10. Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
11. Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
12. Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
13. Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
14. Vacuum leaks in booster system (TMT made)
Click here
15. Vacuum leaks in booster system (TSAM made)
Click here
Noise from brakes
1. Pad (cracked, distorted, dirty or glazed, TMT made)
Click here
2. Pad (cracked, distorted, dirty or glazed, TSAM made)
Click here
3. Lining (cracked, distorted, dirty or glazed)
Click here
4. Installation bolt (TMT made)
Click here
5. Installation bolt (TSAM made)
Click here
6. Disc (scored, TMT made)
Click here
7. Disc (scored, TSAM made)
Click here
8. Pad support plate (loose, TMT made)
Click here
9. Pad support plate (loose, TSAM made)
Click here
10. Anchor, return or tension spring (faulty)
Click here
11. Anti squeal shim (damaged, TMT made)
Click here
12. Anti squeal shim (damaged, TSAM made)
Click here
13. Shoe hold down spring (damaged)
Click here

Brake system (4WD LHD) 
Symptom
Suspected Area
See page
Low pedal or spongy pedal
1. Fluid leaks in brake system
-
2. Air in brake system (TMT made)
Click here
3. Piston seals (worn or damaged, TMT made)
Click here
4. Rear brake shoe clearance (adjustment necessary)
Click here
5. Brake master cylinder (faulty, TMT made w/ ABS)
Click here
6. Brake master cylinder (faulty, TMT made w/o ABS)
Click here
7. Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
8. Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Brake drag
1. Brake pedal free play (minimal)
Click here
2. Parking brake shoe lever travel (adjustment necessary)
Click here
3. No. 1 parking brake wire (stuck)
Click here
4. No. 2 parking brake wire (stuck)
Click here
5. No. 3 parking brake wire (stuck)
Click here
6. Rear brake shoe clearance (adjustment necessary)
Click here
7. Pad (cracked or distorted, TMT made)
Click here
8. Lining (cracked or distorted)
Click here
9. Front brake piston (stuck or frozen, TMT made)
Click here
10. Rear brake piston (stuck or frozen)
Click here
11. Tension or return spring (faulty)
Click here
12. Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
13. Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
14. Vacuum leaks in booster system (TMT made)
Click here
15. Brake master cylinder (faulty, TMT made w/ ABS)
Click here
16. Brake master cylinder (faulty, TMT made w/o ABS)
Click here
Brake pull
1. Front brake piston (stuck or frozen, TMT made)
Click here
2. Rear brake piston (stuck or frozen)
Click here
3. Pad (oily, cracked or distorted, TMT made)
Click here
4. Lining (oily, cracked or distorted)
Click here
5. Disc (scored, TMT made)
Click here
Brake pedal is depressed firmly but brake is insufficient
1. Fluid leaks in brake system
-
2. Air in brake system (TMT made)
Click here
3. Pad (worn, cracked, distorted, oily or glazed, TMT made)
Click here
4. Lining (worn, cracked, distorted, oily or glazed)
Click here
5. Rear brake shoe clearance (adjustment necessary)
Click here
6. Disc (scored, TMT made)
Click here
7. Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
8. Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
9. Vacuum leaks in booster system (TMT made)
Click here
Noise from brakes
1. Pad (cracked, distorted, dirty or glazed, TMT made)
Click here
2. Lining (cracked, distorted, dirty or glazed)
Click here
3. Installation bolt (TMT made)
Click here
4. Disc (scored, TMT made)
Click here
5. Anchor, return or tension spring (faulty)
Click here
6. Anti squeal shim (damaged, TMT made)
Click here
7. Shoe hold down spring (damaged)
Click here

Brake system (4WD RHD) 
Symptom
Suspected Area
See page
Low pedal or spongy pedal
1. Fluid leaks in brake system
-
2. Air in brake system (TMT made)
Click here
3. Air in brake system (TSAM made)
Click here
4. Piston seals (worn or damaged, TMT made)
Click here
5. Piston seals (worn or damaged, TSAM made)
Click here
6. Rear brake shoe clearance (adjustment necessary)
Click here
7. Brake master cylinder (faulty, TMT made w/ ABS)
Click here
8. Brake master cylinder (faulty, TMT made w/o ABS)
Click here
9. Brake master cylinder (faulty, TSAM made w/ ABS)
Click here
10. Brake master cylinder (faulty, TSAM made w/o ABS)
Click here
11. Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
12. Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
13. Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
14. Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Brake drag
1. Brake pedal free play (minimal)
Click here
2. Parking brake shoe lever travel (adjustment necessary)
Click here
3. No. 1 parking brake wire (stuck)
Click here
4. No. 2 parking brake wire (stuck)
Click here
5. No. 3 parking brake wire (stuck)
Click here
6. Rear brake shoe clearance (adjustment necessary)
Click here
7. Pad (cracked or distorted, TMT made)
Click here
8. Pad (cracked or distorted, TSAM made)
Click here
9. Lining (cracked or distorted)
Click here
10. Front brake piston (stuck or frozen, TMT made)
Click here
11. Front brake piston (stuck or frozen, TSAM made)
Click here
12. Rear brake piston (stuck or frozen)
Click here
13. Tension or return spring (faulty)
Click here
14. Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
15. Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
16. Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
17. Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
18. Vacuum leaks in booster system (TMT made)
Click here
19. Vacuum leaks in booster system (TSAM made)
Click here
20. Brake master cylinder (faulty, TMT made w/ ABS)
Click here
21. Brake master cylinder (faulty, TMT made w/o ABS)
Click here
22. Brake master cylinder (faulty, TSAM made w/ ABS)
Click here
23. Brake master cylinder (faulty, TSAM made w/o ABS)
Click here
Brake pull
1. Front brake piston (stuck or frozen, TMT made)
Click here
2. Front brake piston (stuck or frozen, TSAM made)
Click here
3. Rear brake piston (stuck or frozen)
Click here
4. Pad (oily, cracked or distorted, TMT made)
Click here
5. Pad (oily, cracked or distorted, TSAM made)
Click here
6. Lining (oily, cracked or distorted)
Click here
7. Disc (scored, TMT made)
Click here
8. Disc (scored, TSAM made)
Click here
Brake pedal is depressed firmly but brake is insufficient
1. Fluid leaks in brake system
-
2. Air in brake system (TMT made)
Click here
3. Air in brake system (TSAM made)
Click here
4. Pad (worn, cracked, distorted, oily or glazed, TMT made)
Click here
5. Pad (worn, cracked, distorted, oily or glazed, TSAM made)
Click here
6. Lining (worn, cracked, distorted, oily or glazed)
Click here
7. Rear brake shoe clearance (adjustment necessary)
Click here
8. Disc (scored, TMT made)
Click here
9. Disc (scored, TSAM made)
Click here
10. Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
11. Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
12. Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
13. Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
14. Vacuum leaks in booster system (TMT made)
Click here
15. Vacuum leaks in booster system (TSAM made)
Click here
Noise from brakes
1. Pad (cracked, distorted, dirty or glazed, TMT made)
Click here
2. Pad (cracked, distorted, dirty or glazed, TSAM made)
Click here
3. Lining (cracked, distorted, dirty or glazed)
Click here
4. Installation bolt (TMT made)
Click here
5. Installation bolt (TSAM made)
Click here
6. Disc (scored, TMT made)
Click here
7. Disc (scored, TSAM made)
Click here
8. Anchor, return or tension spring (faulty)
Click here
9. Anti squeal shim (damaged, TMT made)
Click here
10. Anti squeal shim (damaged, TSAM made)
Click here
11. Shoe hold down spring (damaged)
Click here

Brake system (Pre-runner) 
Symptom
Suspected Area
See page
Low pedal or spongy pedal
1. Fluid leaks in brake system
-
2. Air in brake system
Click here
3. Piston seals (worn or damaged)
Click here
4. Rear brake shoe clearance (adjustment necessary)
Click here
5. Brake master cylinder (faulty, w/ ABS)
Click here
6. Brake master cylinder (faulty, w/o ABS)
Click here
7. Booster push rod (adjustment necessary, w/ ABS)
Click here
8. Booster push rod (adjustment necessary, w/o ABS)
Click here
Brake drag
1. Brake pedal free play (minimal)
Click here
2. Parking brake shoe lever travel (adjustment necessary)
Click here
3. No. 1 parking brake wire (stuck)
Click here
4. No. 2 parking brake wire (stuck)
Click here
5. No. 3 parking brake wire (stuck)
Click here
6. Rear brake shoe clearance (adjustment necessary)
Click here
7. Pad (cracked or distorted)
Click here
8. Lining (cracked or distorted)
Click here
9. Front brake piston (stuck or frozen)
Click here
10. Rear brake piston (stuck or frozen)
Click here
11. Tension or return spring (faulty)
Click here
12. Booster push rod (adjustment necessary, w/ ABS)
Click here
13. Booster push rod (adjustment necessary, w/o ABS)
Click here
14. Vacuum leaks in booster system
Click here
15. Brake master cylinder (faulty, w/ ABS)
Click here
16. Brake master cylinder (faulty, w/o ABS)
Click here
Brake pull
1. Front brake piston (stuck or frozen)
Click here
2. Rear brake piston (stuck or frozen)
Click here
3. Pad (oily, cracked or distorted)
Click here
4. Lining (oily, cracked or distorted)
Click here
5. Disc (scored)
Click here
Brake pedal is depressed firmly but brake is insufficient
1. Fluid leaks in brake system
-
2. Air in brake system
Click here
3. Pad (worn, cracked, distorted, oily or glazed)
Click here
4. Lining (worn, cracked, distorted, oily or glazed)
Click here
5. Rear brake shoe clearance (adjustment necessary)
Click here
6. Disc (scored)
Click here
7. Booster push rod (adjustment necessary, w/ ABS)
Click here
8. Booster push rod (adjustment necessary, w/o ABS)
Click here
9. Vacuum leaks in booster system
Click here
Noise from brakes
1. Pad (cracked, distorted, dirty or glazed)
Click here
2. Lining (cracked, distorted, dirty or glazed)
Click here
3. Installation bolt
Click here
4. Disc (scored)
Click here
5. Anchor, return or tension spring (faulty)
Click here
6. Anti squeal shim (damaged)
Click here
7. Shoe hold down spring (damaged)
Click here