Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > INSTALLATION

for Preparation Click here



1. INSTALL AIR CONDITIONING UNIT ASSEMBLY


    I045585E01
  1. Install the A/C unit with the bolt and nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



2. INSTALL INSTRUMENT PANEL REINFORCEMENT


  1. Install the instrument panel reinforcement with the 7 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    I045584



  1. Install the 3 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



    I045583

  1. Connect the connectors.



  1. Attach the 12 clamps.


    I045582E01



    I045594E01
  1. Install the grommet to the vehicle body.



    I045581E01
  1. Connect the ground wires to the instrument panel reinforcement with the 2 bolts.



    E111655E01
  1. Connect the connector and wire harness.

  1. w/o PTC heater:
    Attach the 2 clamps.

  1. w/ PTC heater:
    Attach the 3 clamps.



    I045577E01
  1. Connect the connector and wire harness.

  1. Attach the 2 clamps.



3. INSTALL NO.1 COOLER UNIT DRAIN HOSE


I045579E01
  1. Install the drain hose.



4. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Air Conditioning System)


    E110996E01
  1. Install the A/C amplifier with the screw.

  1. Connect the connector.

  1. Attach the clamp to install the amplifier.



5. INSTALL NO. 4 AIR DUCT


E110995E01
  1. Attach the 2 claws to install the duct.



6. INSTALL NO. 2 AIR DUCT


E110994E01
  1. Attach the 2 claws to install the duct.



7. INSTALL NO. 1 AIR DUCT


E110993E01
  1. Attach the 2 claws to install the duct.



8. INSTALL ECM
For 1TR-FE
For 2TR-FE
For 1GR-FE
For 1KD-FTV
For 2KD-FTV


9. INSTALL STEERING COLUMN ASSEMBLY
  1. Install the steering column with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



10. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


I045576E01
  1. Connect the connectors to install the instrument panel junction block.

  1. Attach the 2 clamps to install the brace.

  1. Install the brace with the 3 nuts and 2 bolts.



11. INSTALL NO. 3 HEATER TO REGISTER DUCT


I045575E01
  1. Attach the 4 claws to install the duct.



12. INSTALL NO. 1 HEATER TO REGISTER DUCT


I043959E01
  1. Attach the 3 claws to install the duct.



13. INSTALL NO. 2 HEATER TO REGISTER DUCT


I043958E01
  1. Install the clip and duct.



14. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY LOWER
  1. Install the instrument panel sub-assembly lower (Click here).



15. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY UPPER
  1. Install the instrument panel sub-assembly upper (Click here).



16. CONNECT WATER HOSE SUB-ASSEMBLY


    E110992
  1. Connect the water hose and attach the clip.



17. CONNECT WATER HOSE SUB-ASSEMBLY B

HINT:
Use the same procedures described for the water hose.



18. CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/ Air Conditioning System)
  1. Remove the vinyl tape attached to the tube.

  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the A/C tube.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings on the A/C tube.

  1. Connect the A/C tube and accessory and attach the piping clamp.



19. CONNECT SUCTION TUBE SUB-ASSEMBLY (w/ Air Conditioning System)


    I043225E01
  1. Remove the vinyl tape attached to the tube.

  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the suction tube.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings on the suction tube.

  1. Connect the suction tube and attach the piping clamp.

    HINT:
    After the connection, check that the claw of the piping clamp is engaged.



20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


21. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



22. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).



23. ADD ENGINE COOLANT
For 1TR-FE
For 2TR-FE
For 1GR-FE
For 1KD-FTV
For 2KD-FTV


24. CHARGE REFRIGERANT
SST
09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    450 +- 30 g (15.87 +- 1.05 oz.)



    I037365E02

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
    1. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, and not with the sight glass.



25. WARM UP ENGINE
  1. Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging refrigerant.

    NOTICE:
    After removing and installing the cooler refrigerant lines (with the compressor), be sure to warm up the compressor when turning the A/C switch ON. This is done to prevent damage to the compressor.



26. CHECK FOR ENGINE COOLANT LEAKS
For 1TR-FE
For 2TR-FE
For 1GR-FE
For 1KD-FTV
For 2KD-FTV


27. CHECK FOR LEAKAGE OF REFRIGERANT
  1. After recharging the refrigerant gas, prepare the vehicle for a refrigerant gas leakage check by making sure the following conditions are met.

    1. The ignition switch is OFF.
    2. The vehicle is in a place with good air ventilation and without any volatile gases, such as evaporated gasoline or exhaust gas. The detector is very sensitive to volatile gases. If volatile gases are unavoidable, the vehicle must be lifted up.
    3. Some refrigerant is remaining in the refrigerant system.
    4. The compressor is OFF and its pressure is approximately 392 to 588 kPa (4 to 6 kgf/cm2).



    I042222E03
  1. Check for refrigerant gas leakage from the refrigerant line.

    1. After the blower motor stops, wait at least 15 minutes.

    2. Using a gas leak detector, check that gas is not leaking from the refrigerant line. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Check for refrigerant gas leakage from the cooling unit.

    1. Hold the gas leak detector so that the sensor is under the drain hose, as shown in the illustration.

    2. Check that gas is not leaking from the drain hose. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Check for refrigerant gas leakage from the cooling unit.

    1. Remove the blower motor control from the unit. Insert the gas leak detector's sensor into the unit.

    2. Check that gas is not leaking from the unit. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Check for refrigerant gas leakage from the pressure switch.

    1. Disconnect the pressure switch connector and wait approximately 20 minutes.

    2. Using a gas leak detector, check that gas is not leaking from the pressure switch. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Repeat all steps above 2 to 3 times.