AIR CONDITIONING UNIT (for Automatic Air Conditioning System) > INSTALLATION |
| 1. INSTALL AIR CONDITIONING UNIT ASSEMBLY |
![]() |
Install the air conditioning unit with the bolt and nut.
| 2. INSTALL INSTRUMENT PANEL REINFORCEMENT |
Install the instrument panel reinforcement with the 6 bolts.

Install the 3 bolts.

Connect the connectors.
Attach the 13 clamps.

![]() |
Install the grommet to the vehicle body.
![]() |
Connect the ground wires to the instrument panel reinforcement with the 2 bolts.
![]() |
Connect the 2 connectors.
Attach the clamp.
![]() |
Connect the connector and wire harness.
Attach the clamp.
Install the drain hose.
| 3. INSTALL ECM |
for 1GR-FE:
Install the ECM (Click here).
for 1KD-FTV:
Install the ECM (Click here).
for 2KD-FTV:
Install the ECM (Click here).
for 2TR-FE:
Install the ECM (Click here).
| 4. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY |
![]() |
Install the instrument panel junction block with the 2 nuts.
Connect the connectors.
Install the brace with the nut and 2 bolts.
| 5. INSTALL NO. 4 AIR DUCT |
![]() |
Attach the 2 claws to install the air duct.
| 6. INSTALL NO. 2 AIR DUCT |
![]() |
Attach the 2 claws to install the air duct.
| 7. INSTALL NO. 1 AIR DUCT |
![]() |
Attach the 2 claws to install the air duct.
| 8. INSTALL NO. 3 HEATER TO REGISTER DUCT |
![]() |
Attach the 4 claws to install the duct.
Install the clip.
| 9. INSTALL NO. 1 HEATER TO REGISTER DUCT |
![]() |
Attach the 3 claws to install the duct.
Install the clip.
| 10. INSTALL NO. 2 HEATER TO REGISTER DUCT |
![]() |
Install the duct with the clip.
| 11. INSTALL STEERING COLUMN ASSEMBLY |
Install the steering column assembly (Click here).
| 12. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
Install the lower instrument panel (Click here).
| 13. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
Install the upper instrument panel (Click here).
| 14. CONNECT HEATER WATER HOSE OUTLET A |
Connect the water outlet hose and attach the clip.
| 15. CONNECT HEATER WATER HOSE INLET A |
Connect the water inlet hose and attach the clip.
| 16. CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY |
Remove the vinyl tape attached to the air conditioning tube and accessory.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory.
Install the O-ring to the air conditioning tube and accessory.
Connect the air conditioning tube and accessory.
| 17. CONNECT SUCTION TUBE SUB-ASSEMBLY |
![]() |
Remove the vinyl tape attached to the tube.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction tube.
Install the O-ring to the suction tube.
Connect the suction tube and attach the piping clamp.
Install the bolt.
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 19. CHECK SRS WARNING LIGHT |
Check the SRS warning light (Click here).
| 20. ADD ENGINE COOLANT |
for 1GR-FE:
Add engine coolant .
for 1KD-FTV (w/ EGR Cooler):
Add engine coolant .
for 1KD-FTV (w/o EGR Cooler):
Add engine coolant .
for 2KD-FTV (w/ EGR Cooler):
Add engine coolant .
for 2KD-FTV (w/o EGR Cooler):
Add engine coolant .
for 2TR-FE:
Add engine coolant .
| 21. CHARGE REFRIGERANT |
Perform vacuum purging using a vacuum pump.
Charge refrigerant HFC-134a (R134a).

| 22. WARM UP ENGINE |
Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging refrigerant.
| 23. CHECK FOR ENGINE COOLANT LEAKS |
for 1GR-FE:
Check for engine coolant leaks .
for 1KD-FTV (w/ EGR Cooler):
Check for engine coolant leaks .
for 1KD-FTV (w/o EGR Cooler):
Check for engine coolant leaks .
for 2KD-FTV (w/ EGR Cooler):
Check for engine coolant leaks .
for 2KD-FTV (w/o EGR Cooler):
Check for engine coolant leaks .
for 2TR-FE:
Check for engine coolant leaks .
| 24. CHECK FOR LEAKAGE OF REFRIGERANT |
After recharging the refrigerant gas, prepare the vehicle for a refrigerant gas leakage check by making sure the following conditions are met.
![]() |
Check for refrigerant gas leakage from the refrigerant line.
After the blower motor stops, wait at least 15 minutes.
Using a gas leak detector, check that gas is not leaking from the refrigerant line. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.
Check for refrigerant gas leakage from the cooling unit.
Hold the gas leak detector so that the sensor is under the drain hose, as shown in the illustration.
Check that gas is not leaking from the drain hose. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.
Check for refrigerant gas leakage from the cooling unit.
Remove the blower motor control from the unit. Insert the gas leak detector's sensor into the unit.
Check that gas is not leaking from the unit. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.
Check for refrigerant gas leakage from the pressure switch.
Disconnect the pressure switch connector and wait approximately 20 minutes.
Using a gas leak detector, check that gas is not leaking from the pressure switch. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.
Repeat all steps above 2 to 3 times.