Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › COMPRESSOR AND PULLEY (for 1KD-FTV)

COMPRESSOR AND PULLEY (for 1KD-FTV) > INSTALLATION

for Preparation Click here



1. ADJUST COMPRESSOR OIL
  1. When replacing the compressor with a new one after gradually releasing the refrigerant gas from the service valve, drain the following amount of oil from the new compressor before installation.

    Standard:
    (Oil capacity inside new compressor: 80 + 15 cc (2.7 + 0.5 fl. oz.)) - (Remaining oil amount in the removed compressor) = (Oil amount to be removed when replacing)

    NOTICE:
    1. When checking the compressor oil level, follow the A/C system's precautions.
    2. Since compressor oil remains in the pipes of the vehicle, do not install a new compressor without removing some oil from the vehicle. Excessive oil prevents heat exchange in the refrigerant cycle and causes refrigerant failure.
    3. If the remaining oil in the removed compressor is too low, check for oil leakage.
    4. Be sure to use ND-OIL 8 for compressor oil.



2. INSTALL COOLER COMPRESSOR ASSEMBLY


I043253E02
  1. Install the compressor with the 4 bolts and tighten the bolts in the order shown in the illustration.

    Torque:
    24.5 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. Connect the connector.



3. INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE


I043252E01
  1. Remove the vinyl tape attached to the hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the discharge hose.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



4. INSTALL SUCTION HOSE SUB-ASSEMBLY


I043251E03
  1. Remove the vinyl tape attached to the hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the suction hose.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



5. INSTALL DRIVE BELT


G035153E01
  1. Use the pulley set bolt of the tensioner to rotate the tensioner pulley clockwise, and then install the V belt.

    NOTICE:
    Make sure that the V belt is set properly at each pulley.



    A114802E01
  1. Make sure that the indicator mark of the tensioner is within range A, as shown in the illustration.



6. INSTALL AIR CLEANER ASSEMBLY


    A110353
  1. Connect the air cleaner hose.

  1. Install the air cleaner with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Tighten the clamp.

  1. Install the clamp and connect the IAT connector.

  1. Connect the ventilation hose.

  1. Slide the clamp to the connection of the hose.



7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


8. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



9. CHARGE REFRIGERANT
SST
09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    450 +- 30 g (15.87 +- 1.05 oz.)



    I037365E02

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
    1. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, and not with the sight glass.



10. WARM UP ENGINE
  1. Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging refrigerant.

    NOTICE:
    After removing and installing the cooler refrigerant lines (with the compressor), be sure to warm up the compressor when turning the A/C switch ON. This is done to prevent damage to the compressor.



11. CHECK FOR LEAKAGE OF REFRIGERANT
  1. After recharging the refrigerant gas, prepare the vehicle for a refrigerant gas leakage check by making sure the following conditions are met.

    1. The ignition switch is OFF.
    2. The vehicle is in a place with good air ventilation and without any volatile gases, such as evaporated gasoline or exhaust gas. The detector is very sensitive to volatile gases. If volatile gases are unavoidable, the vehicle must be lifted up.
    3. Some refrigerant is remaining in the refrigerant system.
    4. The compressor is OFF and its pressure is approximately 392 to 588 kPa (4 to 6 kgf/cm2).



    I042222E03
  1. Check for refrigerant gas leakage from the refrigerant line.

    1. After the blower motor stops, wait at least 15 minutes.

    2. Using a gas leak detector, check that gas is not leaking from the refrigerant line. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Check for refrigerant gas leakage from the cooling unit.

    1. Hold the gas leak detector so that the sensor is under the drain hose, as shown in the illustration.

    2. Check that gas is not leaking from the drain hose. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Check for refrigerant gas leakage from the cooling unit.

    1. Remove the blower motor control from the unit. Insert the gas leak detector's sensor into the unit.

    2. Check that gas is not leaking from the unit. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Check for refrigerant gas leakage from the pressure switch.

    1. Disconnect the pressure switch connector and wait approximately 20 minutes.

    2. Using a gas leak detector, check that gas is not leaking from the pressure switch. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Repeat all steps above 2 to 3 times.