DTC P0093 Fuel System Leak Detected - Large Leak |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| After idling for 60 seconds, run engine at 2500 rpm for 30 seconds. Fully depress the accelerator pedal for 5 seconds, and then release it. (*A) Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B) Repeat procedures (*A) and (*B) 5 times. | Fuel leaks in high-pressure areas (1 trip detection logic) |
|
| DTC No. | Data List |
| P0093 |
|
| Engine Speed | Fuel Pressure |
| Idling | Approximately 25000 to 35000 kPa |
| 3000 rpm (No engine load) | Approximately 50000 to 70000 kPa |
| Required sensors | Fuel pressure sensor |
| Frequency of operation | Continuous |
| Duration | 1 second |
| MIL operation | 1 driving cycle |



| Data List | Value | Unit |
| Engine Speed | 1478 | rpm |
| Fuel Press | 8900 | kPa |
| Target Common Rail Pressure | 65320 | kPa |
| Injection Volume (Point A) | 51.26*1 | mm3/st |
| Injection Volume (Point A`) | 9.76 | mm3/st |
| Accel Position | 63.67 | % |
| Injection Feedback Val #1 | -1.1 | mm3/st |
| Injection Feedback Val #2 | -2.5 | mm3/st |
| Injection Feedback Val #3 | 5.0 | mm3/st |
| Injection Feedback Val #4 | -1.8 | mm3/st |
| MIL | ON | - |
| 1.CHECK FOR FUEL LEAKS (IN HIGH-PRESSURE AREAS) |
Before starting the engine, visually check for fuel leaks from the fuel supply pump, fuel injectors, common rail, and the fuel pipes in high-pressure areas.
|
| ||||
| OK | |
| 2.CHECK FOR ANY OTHER DTC OUTPUT (PROCEDURE 2) (IN ADDITION TO DTC P0093 AND RECORD STORED DTC AND FREEZE FRAME DATA) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs and freeze frame data.
| Display (DTC Output) | Proceed to |
| P0093 and "P0190, P0192 and/or P0193" | C |
| P0093 and "P0335 and/or P0339" | B |
| Except above | A |
|
| ||||
|
| ||||
| A | |
| 3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL) |
Check if the fuel level is low.
| Result | Proceed to |
| The indicator (fuel warning light) is illuminated | A |
| The indicator (fuel warning light) is not illuminated | B |
|
| ||||
| A | |
| 4.ADD FUEL |
Add fuel.
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093) |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Start the engine.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Clear DTCs (Click here).
Start the engine. (*A)
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak. (*B)
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)

Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
When no DTCs are output, the air bleeding is completed.
If any DTCs are output, proceed to the next step.
Repeat steps (*A) to (*D).
Clear DTCs (Click here).
Start the engine and warm it up.
Confirm that the shift lever is in neutral and securely apply the parking brake.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*E)
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*F)
Repeat procedures (*E) and (*F) 5 times.

Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
| Display (DTC Output) | Proceed to |
| DTC output | A |
| DTC not output | B |
|
| ||||
| A | |
| 6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4) |
Read the value of Injection Feedback Val #1 to #4 in the Freeze Frame Data recorded in Procedure 2.
| Result | Proceed to |
| Injection Feedback Val for at least one cylinder is 5 mm3/st in at least 1 set of freeze frame data | B |
| Except above | A |
|
| ||||
| A | |
| 7.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
Start the engine.
Read the value of Fuel Press while cranking and idling the engine.
| Result | Proceed to |
| The engine cannot be started or the engine can be started but Fuel Press is less than 20000 kPa 2 seconds after the starter signal changes from OFF to ON. | B |
| Except above | A |
|
| ||||
| A | |
| 8.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.
Read the values.
| Tester Display | Engine Condition* | Normal Value |
| Injection Feedback Val #1 Injection Feedback Val #2 Injection Feedback Val #3 Injection Feedback Val #4 | Idling | -3.0 mm3/st to 3.0 mm3/st |
| Result | Proceed to |
| Injection Feedback Val for at least one cylinder is more than 3 mm3/st and engine vibration is abnormally large | B |
| Except above | A |
|
| ||||
| A | |
| 9.PERFORM ENGINE SPEED ACCELERATION |
Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.
Stop the vehicle and allow the engine to idle.
While checking the tachometer, fully depress the accelerator pedal for 5 seconds, and then release it.*1
Repeat procedure *1 5 times.
| Result | Proceed to |
| No problems such as sluggishness or variations in the tachometer reading | A |
| Except above | B |
|
| ||||
| A | |
| Go to step 11 |
| 10.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER |
Clean the fuel filter case and replace the fuel filter.
| NEXT | |
| 11.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.
![]() |
Take a snapshot with the intelligent tester during the Active Test.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed (Click here).

| Result | Proceed to |
| The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa. | A |
| Except above | B |
|
| ||||
| A | |
| 13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.
| NEXT | |
| 14.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER |
Replace the fuel injector of the malfunctioning cylinder (Click here).
|
| ||||
| 15.REPLACE FUEL INJECTORS OF ALL CYLINDERS |
Replace the fuel injectors (Click here).
| NEXT | |
| 16.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 17.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation code .
Perform the fuel injector pilot quantity learning .
|
| ||||
| 18.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
Read the value while cranking and idling the engine.
| Tester Display | Engine Condition | Specified Condition |
| Engine Speed | Cranking | 50 to 400 rpm |
| Idling with warm engine | 700 to 800 rpm |
|
| ||||
| OK | |
| 19.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE) |
![]() |
Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.
Turn the ignition switch to ON.
Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.


| Tester Connection | Condition | Specified Condition |
| E8-26 (PCR1) - Body ground | Vibration is applied to the wire harness and connectors | No noise in the waveform |
| Result | Proceed to |
| MIL comes on or noise present in the waveform | B |
| Except above | A |
|
| ||||
| A | |
| 20.INSPECT FUEL TEMPERATURE SENSOR (SENSOR OUTPUT) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Fuel Temperature.
Read the value.
|
| ||||
| OK | |
| 21.CHECK FOR INTERMITTENT PROBLEMS |
Check for intermittent problems (Click here).
|
| ||||
| 22.REPLACE CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
|
| ||||
| 23.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR) |
Repair or replace the harness or connector.
| NEXT | |
| 24.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE) |
![]() |
Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.
Turn the ignition switch to ON.
Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
| Tester Connection | Condition | Specified Condition |
| E8-26 (PCR1) - Body ground | Vibration is applied to the wire harness and connectors | No noise in the waveform |
| Result | Proceed to |
| MIL comes on or noise present in the waveform | A |
| Except above | B |
|
| ||||
| A | |
| 25.REPLACE COMMON RAIL ASSEMBLY |
Replace the common rail assembly (Click here).
| NEXT | |
| 26.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
|
| ||||
| 27.REPLACE FUEL TEMPERATURE SENSOR |
Replace the fuel temperature sensor.
| NEXT | |
| 28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / DTC.
Clear DTCs (Click here).
Start the engine.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher)
Confirm that the shift lever is in neutral and securely apply the parking brake.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)
Repeat procedures (*A) and (*B) 5 times.

Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| NEXT | ||
| ||