Home › TRANSMISSION ยท CLUTCH › CLUTCH UNIT

CLUTCH UNIT > INSTALLATION

for Preparation Click here



1. INSTALL INPUT SHAFT FRONT BEARING (for 1KD-FTV, 2KD-FTV, 1GR-FE)


    Q007151E01
  1. Using SST and a hammer, tap in a new bearing.

    SST
    09304-12012  

    HINT:
    After installing the bearing to the hub, make sure that it rotates smoothly.

  1. Install 2 new bolts.

    Torque:
    178 N*m{ 1,815 kgf*cm , 132 ft.*lbf } for 1KD-FTV, 2KD-FTV
    83 N*m{ 846 kgf*cm , 61 ft.*lbf } for 1GR-FE



2. INSTALL INPUT SHAFT FRONT BEARING (for 1TR-FE, 2TR-FE)


    Q007151E01
  1. Using SST and a hammer, tap in a new bearing.

    SST
    09304-12012  

    HINT:
    After installing the bearing to the hub, make sure that it rotates smoothly.

  1. Install 2 new bolts.

    Torque:
    26.5 N*m{ 270 kgf*cm , 20 ft.*lbf }

    HINT:
    The mounting bolts are tightened in 2 progressive steps.



    G035063
  1. Mark the mounting bolts with paint.

  1. Retighten the mounting bolts by 90°in the numerical order shown in the illustration.

  1. Check that the painted marks are now at a 90°angle to the position.



3. INSTALL CLUTCH DISC ASSEMBLY


    C112690E01
  1. Insert SST into the clutch disc. Then insert the SST (together with the clutch disc) into the flywheel.

    SST
    09301-00110  

    NOTICE:
    Take care not to insert the clutch disc facing the wrong direction.



4. INSTALL CLUTCH COVER ASSEMBLY


    D029623E01
  1. Align the matchmarks on the clutch cover and flywheel.

  1. Tighten the 6 bolts as described below.

    1. Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.

    2. Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.

      Torque:
      19 N*m{ 195 kgf*cm , 14 in.*lbf }

  1. Lightly move SST up and down, and right and left.

    SST
    09301-00110  

  1. Check that the disc is in the center, and then tighten the bolts.



5. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY


    D029624E01
  1. Using a dial indicator with roller instrument, measure the diaphragm spring tip alignment.

    Maximum misalignment:
    0.5 mm (0.020 in.)


    1. D029625E01
      If the alignment is not as specified, use SST to adjust the diaphragm spring tip alignment.
    SST
    09333-00013  



6. INSTALL RELEASE FORK SUPPORT
  1. Install the release fork support to the manual transmission unit.



7. INSTALL RELEASE BEARING HUB CLIP
  1. Install the release bearing hub clip to the release bearing.



8. INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY


    C112689E01
  1. Apply Multemp 8158 Grease or equivalent to the following areas:

    1. The contact surfaces of the release fork and release bearing hub.
    2. The contact surfaces of the release fork and push rod.
    3. The pivot points of the release fork.

      Grease:
      Multemp 8158 Grease or equivalent

  1. Install the release fork to the release bearing.



9. INSTALL CLUTCH RELEASE BEARING ASSEMBLY


    D029659E01
  1. Apply clutch spline grease to the input shaft spline.

    Grease:
    Toyota Genuine Clutch Spline Grease or equivalent

  1. Install the release fork (with release bearing) to the manual transmission.

    NOTICE:
    After the installation, move the fork forward and backward to check that the release bearing slides smoothly.



10. INSTALL CLUTCH RELEASE FORK BOOT


11. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY


12. INSTALL FRONT PROPELLER SHAFT ASSEMBLY (4WD)


13. INSTALL REAR PROPELLER SHAFT ASSEMBLY


14. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (4WD)

Torque:
29 N*m{ 296 kgf*cm , 21 ft.*lbf }



15. INSTALL NO. 2 ENGINE COVER SUB-ASSEMBLY (4WD)

Torque:
29 N*m{ 296 kgf*cm , 21 ft.*lbf }



16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


17. PERFORM INITIALIZATION
  1. Perform initialization (Click here ).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



18. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).