Home › TRANSMISSION ยท A343E AUTOMATIC TRANSMISSION › VALVE BODY ASSEMBLY

VALVE BODY ASSEMBLY > INSTALLATION

for Preparation Click here


NOTICE:
When working with seal packing, perform the following:
  1. Using a razor blade and gasket scraper, remove all old seal packing from the gasket surfaces.
  2. Clean all components thoroughly to remove all foreign matter.
  3. Clean both sealing surfaces with a non-residue solvent.
  4. Apply seal packing in a continuous line approximately 2 to 3 mm (0.0787 to 0.118 in.) in diameter on the sealing surface.
  5. Reassemble parts within 10 minutes of applying seal packing. Failing to do so will require the seal packing to be removed and reapplied.



1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


D028710E02
  1. Install the shift solenoid valve SL with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the shift solenoid valve S1 and S2 with the bolt.

    Torque:
    6.6 N*m{ 67 kgf*cm , 58 in.*lbf }

  1. Install the shift solenoid valve SLT with the plate and bolt.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }



    AT08393E04
  1. Align the groove of the manual valve with the pin of the lever.



    D029011E08
  1. Install the 20 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    23 mm (0.91 in.) for A
    28 mm (1.10 in.) for B
    36 mm (1.42 in.) for C



2. CONNECT TRANSMISSION WIRE


G037235E01
  1. Connect the 4 connectors to the 4 shift solenoid valves.



3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


C118025E01
  1. Install 3 new gaskets.



    D028706E03
  1. Install the oil strainer with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    Bolt length:
    14 mm (0.55 in.) for A
    20 mm (0.79 in.) for B
    23 mm (0.91 in.) for C



4. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


D029014E02

HINT:
Remove any packing material and be careful not to spill oil on the contacting surfaces of the transmission case and oil pan.

  1. Install the 3 magnets to the locations indicated in the illustration.



    D028715E01
  1. Apply seal packing to the oil pan as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281,
    Three Bond 1281 or equivalent
    Seal width:
    2 to 3 mm (0.0787 to 0.118 in.)

  1. Install the oil pan with the 19 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



5. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


C118024
  1. Coat a new O-ring with ATF, and install it to the oil filler tube.

  1. Install the oil filler tube with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Install the oil dipstick.



6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



7. PERFORM INITIALIZATION
  1. Perform initialization (Click here).



8. ADD AUTOMATIC TRANSMISSION FLUID

Fluid type:
Toyota Genuine ATF Type T-IV



9. INSPECT AUTOMATIC TRANSMISSION FLUID
  1. Inspect the automatic transmission fluid (Click here).