AUTOMATIC TRANSMISSION ASSEMBLY (for 1KD-FTV) > INSTALLATION |
| 1. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Inspect the torque converter clutch assembly (Click here).
| 2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY |
![]() |
Install the torque converter clutch to the automatic transmission.
Using a vernier caliper measure dimension A between the transmission fitting surface of the engine *1 and the converter fitting surface of the drive plate *2. (#)
![]() |
Using a vernier caliper and straightedge, measure dimension B shown in the illustration. Check that B is greater than A measured in the step labeled (#).
| 3. INSTALL TRANSFER ASSEMBLY |
Install the transfer assembly (Click here).
| 4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY |
![]() |
Apply clutch spline grease to the round of the crankshaft contact surface with the torque converter clutch centerpiece.
![]() |
Install the transmission to the engine with the 5 bolts.
![]() |
Turn the crankshaft to gain access to the installation locations of the 6 torque converter clutch mounting bolts and install each bolt through the hole of the flywheel while holding the crankshaft pulley bolt with a wrench.
| 5. INSTALL STIFFENER PLATE |
![]() |
Install the No. 2 end plate.
Install the No. 4 cylinder block insulator.
Install the stiffener plate LH to the engine and transmission with the 4 bolts.
Install the stiffener plate RH (with oil cooler tube clamp) to the engine and transmission with the 4 bolts.
| 6. INSTALL STARTER ASSEMBLY |
| 7. CONNECT WIRE HARNESS |
| 8. CONNECT CONNECTOR |
Transmission side:
Connect the connectors.
Connect the park/neutral position switch connector.
Connect the transmission wire connector.
Connect the 2 speed sensor connectors.
Transfer side:
Connect the connectors.
Connect the No. 1 indicator switch connector.
Connect the No. 2 indicator switch connector.
Connect the speed sensor connector.
| 9. INSTALL NO. 1 ENGINE MOUNTING INSULATOR REAR |
![]() |
Install the engine mounting insulator to the transmission with the 4 bolts.
| 10. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
![]() |
*1: Install the frame crossmember to the engine mounting insulator with the 4 set bolts.
*2: Connect the ends of the frame crossmember to the vehicle with the 4 bolts and 4 nuts.
| 11. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET |
![]() |
Install the control cable bracket with the 2 bolts.
| 12. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Connect the control cable with the clip and nut.
| 13. CONNECT OIL COOLER TUBE |
![]() |
Connect the end of the oil cooler tube inlet to the automatic transmission by hand.
Connect the end of the oil cooler tube outlet to the automatic transmission by hand.
Install the 3 clamps with the 3 bolts.
![]() |
Using a union nut wrench, tighten the inlet and outlet tubes.
| 14. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY |
Install the propeller shaft with center bearing assembly (Click here).
| 15. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Install the exhaust pipe (Click here).
| 16. INSTALL TRANSFER CASE LOWER PROTECTOR |
Install the protector with the 4 bolts.
| 17. INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY |
![]() |
Install the transfer shift lever to the shift lever retainer.
Using needle-nose pliers, install the snap ring.
Install the transfer high and low shift lever with the 4 bolts.
| 18. INSTALL SHIFT LEVER BOOT ASSEMBLY |
Install the shift lever boot with the 4 screws.
| 19. INSTALL CONSOLE BOX ASSEMBLY |
Install the console box assembly (Click here).
| 20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 21. ADD AUTOMATIC TRANSMISSION FLUID |
Add automatic transmission fluid (Click here).
| 22. INSPECT SHIFT LEVER POSITION |
When moving the shift lever from P to R with the ignition switch to ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.
Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves in reverse after shifting to R.
If the results are not as specified, inspect the park/ neutral position switch and check the shift lever.
| 23. PERFORM INITIALIZATION |
Perform initialization (Click here).
| 24. CHECK FOR EXHAUST GAS LEAK |
| 25. INSTALL NO. 2 ENGINE UNDER COVER |
| 26. INSTALL NO .1 ENGINE UNDER COVER |