Home › ENGINE ยท 1KD-FTV › COOLING › THERMOSTAT (w/ EGR Cooler)

THERMOSTAT (w/ EGR Cooler) > INSTALLATION

for Preparation Click here



1. INSTALL THERMOSTAT


    A110388E01
  1. Install a new gasket to the thermostat.

    HINT:
    When installing the thermostat to the gasket, be careful not to deform the gasket. Make sure that the thermostat is properly installed into the groove of the gasket, as shown in the illustration.

  1. Insert the thermostat into the cylinder block with the jiggle valve facing straight upward.

    HINT:
    The jiggle valve may be set within 30°of either side of the prescribed position.



2. INSTALL WATER INLET


    A097637E01
  1. Install the water inlet with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



3. CONNECT NO. 1 AUTOMATIC TRANSMISSION OIL COOLER TUBE CLAMP (for Automatic Transmission)


    A097634E01
  1. Connect the clamp to the inlet with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



4. INSTALL COMPRESSOR INLET ELBOW


A110341
  1. Install a new gasket and inlet elbow with the 2 nuts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. for Ventilation Pipe Type:
    Install the ventilation hose.

    1. Connect the ventilation pipe to the cylinder head cover.

    2. Move the clamp to the joint pipe of the hose.

    3. Install the ventilation pipe with the bolt.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 connectors to the turbocharger.

  1. Install the harness clamp's clip to the inlet elbow.



5. CONNECT RADIATOR HOSE INLET


6. INSTALL INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR
  1. Install the intake air connector to the air hoses.



    A135919
  1. Install the intercooler with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    A135918
  1. Tighten the 2 clamps.



    A149802
  1. Connect the IAT sensor connector and manifold absolute diesel pressure sensor connector.

  1. Connect the vacuum hose to the manifold absolute pressure sensor.

  1. Attach the 2 clamps.



7. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY


A135916
  1. Install the engine cover with the 3 bolts and 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



8. INSTALL AIR CLEANER ASSEMBLY


A099628E02
  1. Connect the air cleaner hose.

  1. Install the cleaner with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Tighten the hose clamp of the compressor inlet elbow.

  1. for Ventilation Hose Type:
    Connect the ventilation hose.

  1. Connect the MAF meter connector and install the clamp.



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


10. ADD ENGINE COOLANT
  1. Tighten the cylinder block drain cock plug.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the radiator drain cock plug by hand.



    A098989E01
  1. Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.

    Standard capacity:
    Item
    Specified Condition
    A/T
    11.1 liters (11.7 US qts, 9.8 Imp. qts)
    M/T
    9.8 liters (10.4 US qts, 8.6 Imp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.



    A099591E01
  1. Using a wrench, install the vent plug.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

    4. Stop the engine and wait until the coolant cools down to ambient temperature.

      CAUTION:
      Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    G036768E01
  1. After the coolant cools down, check that the coolant level is at the F line.
    If the coolant level is below the F line, add TOYOTA SLLC to the F line.



11. INSPECT FOR COOLANT LEAK

NOTICE:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A097645E01
  1. Fill the radiator with coolant and attach a radiator cap tester to the radiator reservoir.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks.
    If no external leaks are found, check the cylinder block and head.



12. INSTALL NO. 1 ENGINE UNDER COVER (for 4WD)


13. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.